2703022 Phoenix Contact Data & Networking Devices

Ambient temperature (storage/transport)-40 °C ... 85 °C

Electromagnetic compatibilityConformance with EMC Directi...

Color-

Interface 1-

Depth179 mm

External cable diameter-

Supply voltage range-

Connection methodScrew connection

Switch-on threshold-

Local diagnostics-

Humidity-

Type of test-

Height130 mm

Altitude-

Electrical isolation-

Signal1 kV (Test Level 2 - asymmet...

ECLASS 11.027040701

Net weight2.5 kg

Degree of pollution2

ETIM 6.0EC002540

Conductor cross section AWG min.18

Conductor cross section flexible max.4 mm²

Frequency range0.15 MHz ... 80 MHz

Designation-

Power consumption-

Additional text-

Width96 mm

EMC-

Ambient temperature (operation)-25 °C ... 70 °C (> 60 °C De...

Degree of protectionIP20

Indirect discharge-

ECLASS 7.027049002

Housing materialSteel sheet, zinc-plated

Overvoltage category-

REACh SVHCLead 7439-92-1

Note on the connection method-

Stripping length10 mm

Serial transmission speed-

Current carrying capacity-

Mounting type-

MTTF-

Transmission length-

China RoHSEnvironmentally Friendly Use...

Identification-

Standards/regulations-

IEC test classification-

ECLASS 9.027040701

Utilization restriction-

Permissible humidity (operation)-

Conductor cross section flexible min.0.2 mm²

Conductor cross section AWG max.10

Voltage10 V (Test Level 3)

ECLASS 6.027049000

Conductor cross section, flexible, with ferrule, with plastic sleeve-

Interface 2-

Vibration-

Test result-

Rated insulation voltage-

Response time-

Contact discharge8 kV (Test Level 4)

Conductor cross section solid max.6 mm²

Temperature-

ETIM 7.0EC002540

CommentsCriterion A

Conductor cross section flexible, with ferrule without plastic sleeve-

ECLASS 10.0.127040701

Pin assignment-

Maximum output power-

Precision-

Continuous shield current-

Certificate-

Conductor cross section solid min.0.2 mm²

Impedance-

Maximum output current-

Width with alternative assembly176 mm

Climatic class3K3 (in acc. with EN 60721)

AC frequency range45 Hz ... 65 Hz

Mains buffering timetyp. 25 ms (400 V AC)

Nominal output voltage48 V DC ±1 %

Connection in parallelYes, for redundancy and incr...

Connection in seriesyes

Typical response time< 1 s

Environmental protection directive-

Protection classI

Low Voltage DirectiveConformance with Low Voltage...

Flicker-

I/O/Sasymmetrical

Installation distance top/bottom-

Current consumption3x 2.1 A (400 V AC)

Protective circuit/componentVaristor

Dynamic Boost (IDyn.Boost)-

Selective Fuse Breaking (ISFB)100 A (12 ms)

Output power960 W

MTBF (IEC 61709, SN 29500)> 890000 h (25 °C)

Assembly instructionsalignable: PN ≥50%, 5 mm hor...

EMC requirements for noise emissionEN 61000-6-3

Standard - Safety of transformersIEC 61558-2-17

Standard - safety for equipment for measurement, control, and laboratory use-

Standard – Limitation of mains harmonic currentsEN 61000-3-2

Mains variation/undervoltage-

CSACAN/CSA-C22.2 No. 60950-1-07

SIQ-

DNV GL noise radiation-

Discharge in air15 kV (Test Level 4)

Fast transients (burst)EN 61000-4-4

Conducted interferenceEN 61000-4-6

Voltage dips-

Attenuated sinusoidal oscillations (ring wave)-

Test level 4-

Attenuated oscillating wave-

ECLASS 5.127242200

UNSPSC 21.039121004

Depth with alternative assembly99 mm

Installation height4000 m

Frequency range (fN)-

Nominal power consumption1386 VA

Recommended breaker for input protection6 A ... 16 A (AC: Characteri...

Nominal output current (IN)20 A (-25 °C ... 60 °C, UOUT...

Protection against overvoltage at the output (OVP)< 60 V DC

Residual ripple< 50 mVPP (with nominal valu...

Insulation voltage input/output4 kV AC (type test)

EMC requirements for noise immunityEN 61000-6-1

Standard – Safety extra-low voltageIEC 60950-1 (SELV) and EN 60...

UL approvalsUL Listed UL 508

Shipbuilding approval-

Harmonic currents-

Electrostatic dischargeEN 61000-4-2

Electromagnetic HF fieldEN 61000-4-3

Surge voltage load (surge)EN 61000-4-5

Voltage dip-

Test level 1-

Test level 5-

Input, output (test level 2)-

Signals (test level 2)-

UNSPSC 20.039121004

Height with alternative assembly130 mm

Inflammability class in acc. with UL 94 (housing / terminal blocks)-

Discharge current to PE< 3.5 mA

Power factor (cos phi)-

Static Boost (IStat.Boost)-

Feedback voltage resistancemax. 60 V DC

Maximum power dissipation in no-load condition24 W

Efficiency> 93 % (at 400 V AC and nomi...

Insulation voltage input / PE3.5 kV AC (type test)

EMC requirements, power plant-

Standard - Electrical safetyIEC 60950-1/VDE 0805 (SELV)

Standard - power supply devices for low voltage with DC output-

Conducted noise emission-

DNV GL conducted interference-

Test field strength10 V/m (Test Level 3)

Output1 kV (Test Level 2 - symmetr...

Pulse-shape magnetic field-

Asymmetrical conducted disturbance variables-

Test level 6-

Signals (test level 1)-

UNSPSC 13.239121004

Installation distance right/left-

Ambient temperature (start-up type tested)-40 °C

Max. permissible relative humidity (operation)≤ 95 % (at 25 °C, non-conden...

Input voltage range3x 320 V AC ... 575 V AC

Nominal input voltage range3x 400 V AC ... 500 V AC

Inrush current< 20 A (typical)

Type of protectionTransient surge protection

Setting range of the output voltage (USet)30 V DC ... 56 V DC (> 48 V ...

Derating60 °C ... 70 °C (2.5%/K)

Control deviation< 1 % (change in load, stati...

Power loss nominal load max.70 W

Insulation voltage output / PE500 V DC (routine test)

Mounting positionhorizontal DIN rail NS 35, E...

HART FSK Physical Layer Test Specification Compliance-

Standard - Safe isolationDIN VDE 0100-410

Rail applicationsEN 50121-4

Noise emission-

Input2 kV (Test Level 3 - symmetr...

Frequency-

Number of periods-

Test level 3-

Input, output (test level 3)-

Criterion BTemporary impairment to oper...

ECLASS 5.027242200

UNSPSC 18.039121004

Power frequency magnetic field-

Damped oscillating magnetic field-

Test level 2-

Input, output (test level 1)-

Criterion ANormal operating behavior wi...

Criterion C-

UNSPSC 19.039121004

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installationsEN 50178/VDE 0160 (PELV)

ECLASS 4.027040700

POWER BOOST (IBoost)22.5 A (-25 °C ... 40 °C per...

Active current limitationApprox. IBOOST = 22.5 A (for...

ECLASS 4.127040700

ETIM 4.0EC002540

UNSPSC 12.0139121004

Standard - Approval for medical useIEC 60601-1, 2 x MOOP

ETIM 3.0EC001039

UNSPSC 6.0130211502

Standard - Equipment safetyBG (design tested)

Frequency range DC0 Hz

Screw threadM3

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipmentEN 50178

UNSPSC 1139121004

UNSPSC 7.090139121004

Ambient temperature (storage/transport)-40 °C ... 85 °C

Electromagnetic compatibilityConformance with EMC Directi...

Colorgray

Interface 1Ethernet interface, 10/100/1...

Depth86 mm

External cable diameter5.5 mm ... 6.5 mm

Supply voltage range36 V DC ... 52 V DC 10 % (v...

Connection methodRJ45 jack

Switch-on threshold≥ 30 mA

Local diagnosticsYellow LED

HumidityB

Type of testContinuous shock according t...

Height101.3 mm

Altitude≤ 5000 m (For restrictions, ...

Electrical isolationFE // Ethernet

Signal± 1 kV (Data line, asymmetri...

ECLASS 11.019170112

Net weight124.2 g

Degree of pollution2

ETIM 6.0EC002599

Conductor cross section AWG min.26

Conductor cross section flexible max.1.5 mm²

Frequency range0.15 MHz ... 80 MHz

DesignationShipbuilding

Power consumption270 mW (Shield current monit...

Additional textPlease follow the special in...

Width23.8 mm

EMCB

Ambient temperature (operation)-40 °C ... 75 °C

Degree of protectionIP20 (Manufacturer's declara...

Indirect discharge± 6 kV

ECLASS 7.019170112

Housing materialPlastic

Overvoltage categoryII

REACh SVHCLead 7439-92-1

Note on the connection methodCAT5e

Stripping length8 mm

Serial transmission speed10/100/1000 Mbps

Current carrying capacity≤ 1.5 A (≤ 60 W (PoE+))

Mounting typeDIN rail mounting, stationar...

MTTF3281 Years (SN 29500 standar...

Transmission length100 m (including patch cable...

China RoHSEnvironmentally Friendly Use...

IdentificationDNV GL

Standards/regulationsDIN EN 61643-21

IEC test classificationC2

ECLASS 9.019170112

Utilization restrictionEMC: class A product, see ma...

Permissible humidity (operation)10 % ... 95 % (non-condensin...

Conductor cross section flexible min.0.2 mm²

Conductor cross section AWG max.16

Voltage≤ 10 V

ECLASS 6.019170100

Conductor cross section, flexible, with ferrule, with plastic sleeve0.25 mm² ... 1.5 mm² (only t...

Interface 2Ethernet interface, 10/100/1...

VibrationB

Test result10g for 16 ms, 1000 shocks i...

Rated insulation voltage85 V DC

Response time3 s

Contact discharge± 6 kV (Test Level 3)

Conductor cross section solid max.1.5 mm²

TemperatureD

ETIM 7.0EC002599

CommentsCriterion B

Conductor cross section flexible, with ferrule without plastic sleeve0.25 mm² ... 1.5 mm² (only t...

ECLASS 10.0.119170112

Pin assignment1:1

Maximum output power60 W

Precision± 5 %

Continuous shield current≤ 1.5 A

CertificateCSA 22.2 No. 60079-0 Ed. 3 /...

Conductor cross section solid min.0.2 mm²

Impedance≤ 1 Ω

Maximum output current725 mA (PoE)

Width with alternative assembly-

Climatic class-

AC frequency range-

Mains buffering time-

Nominal output voltage-

Connection in parallel-

Connection in series-

Typical response time-

Environmental protection directive-

Protection class-

Low Voltage Directive-

Flicker-

I/O/S-

Installation distance top/bottom-

Current consumption-

Protective circuit/component-

Dynamic Boost (IDyn.Boost)-

Selective Fuse Breaking (ISFB)-

Output power-

MTBF (IEC 61709, SN 29500)-

Assembly instructions-

EMC requirements for noise emission-

Standard - Safety of transformers-

Standard - safety for equipment for measurement, control, and laboratory use-

Standard – Limitation of mains harmonic currents-

Mains variation/undervoltage-

CSA-

SIQ-

DNV GL noise radiation-

Discharge in air-

Fast transients (burst)-

Conducted interference-

Voltage dips-

Attenuated sinusoidal oscillations (ring wave)-

Test level 4-

Attenuated oscillating wave-

ECLASS 5.1-

UNSPSC 21.0-

Depth with alternative assembly-

Installation height-

Frequency range (fN)-

Nominal power consumption-

Recommended breaker for input protection-

Nominal output current (IN)-

Protection against overvoltage at the output (OVP)-

Residual ripple-

Insulation voltage input/output-

EMC requirements for noise immunity-

Standard – Safety extra-low voltage-

UL approvals-

Shipbuilding approval-

Harmonic currents-

Electrostatic discharge-

Electromagnetic HF field-

Surge voltage load (surge)-

Voltage dip-

Test level 1-

Test level 5-

Input, output (test level 2)-

Signals (test level 2)-

UNSPSC 20.0-

Height with alternative assembly-

Inflammability class in acc. with UL 94 (housing / terminal blocks)-

Discharge current to PE-

Power factor (cos phi)-

Static Boost (IStat.Boost)-

Feedback voltage resistance-

Maximum power dissipation in no-load condition-

Efficiency-

Insulation voltage input / PE-

EMC requirements, power plant-

Standard - Electrical safety-

Standard - power supply devices for low voltage with DC output-

Conducted noise emission-

DNV GL conducted interference-

Test field strength-

Output-

Pulse-shape magnetic field-

Asymmetrical conducted disturbance variables-

Test level 6-

Signals (test level 1)-

UNSPSC 13.2-

Installation distance right/left-

Ambient temperature (start-up type tested)-

Max. permissible relative humidity (operation)-

Input voltage range-

Nominal input voltage range-

Inrush current-

Type of protection-

Setting range of the output voltage (USet)-

Derating-

Control deviation-

Power loss nominal load max.-

Insulation voltage output / PE-

Mounting position-

HART FSK Physical Layer Test Specification Compliance-

Standard - Safe isolation-

Rail applications-

Noise emission-

Input-

Frequency-

Number of periods-

Test level 3-

Input, output (test level 3)-

Criterion B-

ECLASS 5.0-

UNSPSC 18.0-

Power frequency magnetic field-

Damped oscillating magnetic field-

Test level 2-

Input, output (test level 1)-

Criterion A-

Criterion C-

UNSPSC 19.0-

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

ECLASS 4.0-

POWER BOOST (IBoost)-

Active current limitation-

ECLASS 4.1-

ETIM 4.0-

UNSPSC 12.01-

Standard - Approval for medical use-

ETIM 3.0-

UNSPSC 6.01-

Standard - Equipment safety-

Frequency range DC-

Screw thread-

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment-

UNSPSC 11-

UNSPSC 7.0901-

Ambient temperature (storage/transport)-40 °C ... 85 °C

Electromagnetic compatibilityConformance with EMC Directi...

Color-

Interface 1-

Depth125 mm

External cable diameter-

Supply voltage range-

Connection methodPush-in connection

Switch-on threshold-

Local diagnostics-

Humidity-

Type of test-

Height130 mm

Altitude-

Electrical isolation-

Signal1 kV (Test Level 2 - asymmet...

ECLASS 11.027040701

Net weight1.1 kg

Degree of pollution2

ETIM 6.0EC002540

Conductor cross section AWG min.24

Conductor cross section flexible max.1.5 mm²

Frequency range50 Hz ... 60 Hz

Designation-

Power consumption-

Additional textTest Level 2

Width70 mm

EMC-

Ambient temperature (operation)-25 °C ... 70 °C (> 60 °C De...

Degree of protectionIP20

Indirect discharge-

ECLASS 7.027049002

Housing material-

Overvoltage category-

REACh SVHCLead 7439-92-1

Note on the connection method-

Stripping length8 mm

Serial transmission speed-

Current carrying capacity-

Mounting type-

MTTF-

Transmission length-

China RoHSEnvironmentally Friendly Use...

Identification-

Standards/regulations-

IEC test classification-

ECLASS 9.027040701

Utilization restriction-

Permissible humidity (operation)-

Conductor cross section flexible min.0.2 mm²

Conductor cross section AWG max.16

Voltage2.5 kV

ECLASS 6.027049000

Conductor cross section, flexible, with ferrule, with plastic sleeve-

Interface 2-

Vibration-

Test result-

Rated insulation voltage-

Response time-

Contact discharge8 kV (Test Level 4)

Conductor cross section solid max.1 mm²

Temperature-

ETIM 7.0EC002540

CommentsCriterion A

Conductor cross section flexible, with ferrule without plastic sleeve-

ECLASS 10.0.127040701

Pin assignment-

Maximum output power-

Precision-

Continuous shield current-

Certificate-

Conductor cross section solid min.0.2 mm²

Impedance-

Maximum output current-

Width with alternative assembly122 mm

Climatic class3K3 (in acc. with EN 60721)

AC frequency range50 Hz ... 60 Hz -10 % ... +1...

Mains buffering timetyp. 33 ms (3x 400 V AC)

Nominal output voltage24 V DC

Connection in parallelYes, for redundancy and incr...

Connection in seriesyes

Typical response time300 ms (from SLEEP MODE)

Environmental protection directiveRoHS Directive 2011/65/EU

Protection classI

Low Voltage DirectiveConformance with Low Voltage...

FlickerEN 61000-3-3

I/O/Sasymmetrical

Installation distance top/bottom50 mm / 50 mm

Current consumption3x 0.99 A (400 V AC)

Protective circuit/componentVaristor, gas-filled surge a...

Dynamic Boost (IDyn.Boost)30 A (5 s)

Selective Fuse Breaking (ISFB)120 A (15 ms)

Output power480 W

MTBF (IEC 61709, SN 29500)> 985000 h (25 °C)

Assembly instructionsalignable: PN ≥50%, 5 mm hor...

EMC requirements for noise emissionEN 61000-6-3

Standard - Safety of transformersIEC 61558-2-16 pending

Standard - safety for equipment for measurement, control, and laboratory useIEC 61010-1

Standard – Limitation of mains harmonic currentsEN 61000-3-2

Mains variation/undervoltageSEMI F47-0706, EN 61000-4-11

CSACAN/CSA-C22.2 No. 60950-1-07

SIQBG (type approved)

DNV GL noise radiationClass B

Discharge in air15 kV (Test Level 4)

Fast transients (burst)EN 61000-4-4

Conducted interferenceEN 61000-4-6

Voltage dipsEN 61000-4-11

Attenuated sinusoidal oscillations (ring wave)EN 61000-4-12

Test level 415 kHz 150 kHz (Test Level 4...

Attenuated oscillating waveEN 61000-4-18

ECLASS 5.127242200

UNSPSC 21.039121004

Depth with alternative assembly73 mm

Installation height≤ 5000 m (> 2000 m, observe ...

Frequency range (fN)50 Hz ... 60 Hz -10 % ... +1...

Nominal power consumption541 VA

Recommended breaker for input protection3x 4 A ... 20 A (Characteris...

Nominal output current (IN)20 A

Protection against overvoltage at the output (OVP)≤ 32 V DC

Residual ripple< 60 mVPP (with nominal valu...

Insulation voltage input/output4 kV AC (type test)

EMC requirements for noise immunityEN 61000-6-1

Standard – Safety extra-low voltageIEC 61010-1 (SELV)

UL approvalsUL Listed UL 508

Shipbuilding approvalDNV GL, PRS, BV, LR, ABS

Harmonic currentsEN 61000-3-2

Electrostatic dischargeEN 61000-4-2

Electromagnetic HF fieldEN 61000-4-3

Surge voltage load (surge)EN 61000-4-5

Voltage dip0 %

Test level 115 Hz 150 Hz (Test Level 4)

Test level 516.7 Hz 50 Hz 60 Hz (Test Le...

Input, output (test level 2)10 MHz

Signals (test level 2)100 kHz 1 MHz (Test Level 3 ...

UNSPSC 20.039121004

Height with alternative assembly130 mm

Inflammability class in acc. with UL 94 (housing / terminal blocks)V0

Discharge current to PE< 3.5 mA

Power factor (cos phi)0.94

Static Boost (IStat.Boost)25 A

Feedback voltage resistance≤ 35 V DC

Maximum power dissipation in no-load condition< 7 W (400 V AC)

Efficiencytyp. 93.9 % (400 V AC)

Insulation voltage input / PE3.5 kV AC (type test)

EMC requirements, power plantIEC 61850-3

Standard - Electrical safetyIEC 61010-2-201 (SELV)

Standard - power supply devices for low voltage with DC outputEN 61204-3

Conducted noise emissionEN 55016

DNV GL conducted interferenceClass A

Test field strength110 A/m

Output1 kV (Test Level 3 - symmetr...

Pulse-shape magnetic fieldEN 61000-4-9

Asymmetrical conducted disturbance variablesEN 61000-4-16

Test level 616.7 Hz 50 Hz 60 Hz (Test Le...

Signals (test level 1)100 kHz 1 MHz (Test Level 3 ...

UNSPSC 13.239121004

Installation distance right/left5 mm / 5 mm

Ambient temperature (start-up type tested)-40 °C

Max. permissible relative humidity (operation)≤ 95 % (at 25 °C, non-conden...

Input voltage range3x 400 V AC ... 500 V AC -20...

Nominal input voltage range3x 400 V AC ... 500 V AC

Inrush currenttyp. 2 A (at 25 °C)

Type of protectionTransient surge protection

Setting range of the output voltage (USet)24 V DC ... 29.5 V DC (const...

Derating> 60 °C ... 70 °C (2.5%/K)

Control deviation< 0.5 % (Static load change ...

Power loss nominal load max.< 32 W (400 V AC)

Insulation voltage output / PE0.5 kV DC (type test)

Mounting positionhorizontal DIN rail NS 35, E...

HART FSK Physical Layer Test Specification ComplianceOutput voltage UOut complian...

Standard - Safe isolationIEC 61558-2-16 pending

Rail applicationsEN 50121-3-2

Noise emissionEN 55016

Input2 kV (Test Level 4 - symmetr...

Frequency50 Hz

Number of periods0,5 / 1 / 5 / 50 / 250 perio...

Test level 31.5 kHz 15 kHz (Test Level 4...

Input, output (test level 3)100 kHz 1 MHz (Test Level 3 ...

Criterion BTemporary impairment to oper...

ECLASS 5.027242200

UNSPSC 18.039121004

Power frequency magnetic fieldEN 61000-4-8

Damped oscillating magnetic fieldEN 61000-4-10

Test level 2150 Hz 1.5 kHz (Test Level 4...

Input, output (test level 1)100 kHz 1 MHz (Test Level 3 ...

Criterion ANormal operating behavior wi...

Criterion CTemporary adverse effects on...

UNSPSC 19.039121004

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

ECLASS 4.0-

POWER BOOST (IBoost)-

Active current limitation-

ECLASS 4.1-

ETIM 4.0-

UNSPSC 12.01-

Standard - Approval for medical use-

ETIM 3.0-

UNSPSC 6.01-

Standard - Equipment safety-

Frequency range DC-

Screw thread-

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment-

UNSPSC 11-

UNSPSC 7.0901-

Ambient temperature (storage/transport)-40 °C ... 85 °C

Electromagnetic compatibilityConformance with EMC Directi...

Color-

Interface 1-

Depth179 mm

External cable diameter-

Supply voltage range-

Connection methodScrew connection

Switch-on threshold-

Local diagnostics-

Humidity-

Type of test-

Height130 mm

Altitude-

Electrical isolation-

Signal1 kV (Test Level 2 - asymmet...

ECLASS 11.027040701

Net weight2.5 kg

Degree of pollution2

ETIM 6.0EC002540

Conductor cross section AWG min.18

Conductor cross section flexible max.4 mm²

Frequency range0.15 MHz ... 80 MHz

Designation-

Power consumption-

Additional text-

Width96 mm

EMC-

Ambient temperature (operation)-25 °C ... 70 °C (> 60 °C De...

Degree of protectionIP20

Indirect discharge-

ECLASS 7.027049002

Housing materialSteel sheet, zinc-plated

Overvoltage category-

REACh SVHCLead 7439-92-1

Note on the connection method-

Stripping length10 mm

Serial transmission speed-

Current carrying capacity-

Mounting type-

MTTF-

Transmission length-

China RoHSEnvironmentally Friendly Use...

Identification-

Standards/regulations-

IEC test classification-

ECLASS 9.027040701

Utilization restriction-

Permissible humidity (operation)-

Conductor cross section flexible min.0.2 mm²

Conductor cross section AWG max.10

Voltage10 V (Test Level 3)

ECLASS 6.027049000

Conductor cross section, flexible, with ferrule, with plastic sleeve-

Interface 2-

Vibration-

Test result-

Rated insulation voltage-

Response time-

Contact discharge8 kV (Test Level 4)

Conductor cross section solid max.6 mm²

Temperature-

ETIM 7.0EC002540

CommentsCriterion A

Conductor cross section flexible, with ferrule without plastic sleeve-

ECLASS 10.0.127040701

Pin assignment-

Maximum output power-

Precision-

Continuous shield current-

Certificate-

Conductor cross section solid min.0.2 mm²

Impedance-

Maximum output current-

Width with alternative assembly176 mm

Climatic class3K3 (in acc. with EN 60721)

AC frequency range45 Hz ... 65 Hz

Mains buffering timetyp. 25 ms (400 V AC)

Nominal output voltage48 V DC ±1 %

Connection in parallelYes, for redundancy and incr...

Connection in seriesyes

Typical response time< 1 s

Environmental protection directive-

Protection classI

Low Voltage DirectiveConformance with Low Voltage...

Flicker-

I/O/Sasymmetrical

Installation distance top/bottom-

Current consumption3x 2.1 A (400 V AC)

Protective circuit/componentVaristor

Dynamic Boost (IDyn.Boost)-

Selective Fuse Breaking (ISFB)100 A (12 ms)

Output power960 W

MTBF (IEC 61709, SN 29500)> 890000 h (25 °C)

Assembly instructionsalignable: PN ≥50%, 5 mm hor...

EMC requirements for noise emissionEN 61000-6-3

Standard - Safety of transformersIEC 61558-2-17

Standard - safety for equipment for measurement, control, and laboratory use-

Standard – Limitation of mains harmonic currentsEN 61000-3-2

Mains variation/undervoltage-

CSACAN/CSA-C22.2 No. 60950-1-07

SIQ-

DNV GL noise radiation-

Discharge in air15 kV (Test Level 4)

Fast transients (burst)EN 61000-4-4

Conducted interferenceEN 61000-4-6

Voltage dips-

Attenuated sinusoidal oscillations (ring wave)-

Test level 4-

Attenuated oscillating wave-

ECLASS 5.127242200

UNSPSC 21.039121004

Depth with alternative assembly99 mm

Installation height4000 m

Frequency range (fN)-

Nominal power consumption1386 VA

Recommended breaker for input protection6 A ... 16 A (AC: Characteri...

Nominal output current (IN)20 A (-25 °C ... 60 °C, UOUT...

Protection against overvoltage at the output (OVP)< 60 V DC

Residual ripple< 50 mVPP (with nominal valu...

Insulation voltage input/output4 kV AC (type test)

EMC requirements for noise immunityEN 61000-6-1

Standard – Safety extra-low voltageIEC 60950-1 (SELV) and EN 60...

UL approvalsUL Listed UL 508

Shipbuilding approval-

Harmonic currents-

Electrostatic dischargeEN 61000-4-2

Electromagnetic HF fieldEN 61000-4-3

Surge voltage load (surge)EN 61000-4-5

Voltage dip-

Test level 1-

Test level 5-

Input, output (test level 2)-

Signals (test level 2)-

UNSPSC 20.039121004

Height with alternative assembly130 mm

Inflammability class in acc. with UL 94 (housing / terminal blocks)-

Discharge current to PE< 3.5 mA

Power factor (cos phi)-

Static Boost (IStat.Boost)-

Feedback voltage resistancemax. 60 V DC

Maximum power dissipation in no-load condition24 W

Efficiency> 93 % (at 400 V AC and nomi...

Insulation voltage input / PE3.5 kV AC (type test)

EMC requirements, power plant-

Standard - Electrical safetyIEC 60950-1/VDE 0805 (SELV)

Standard - power supply devices for low voltage with DC output-

Conducted noise emission-

DNV GL conducted interference-

Test field strength10 V/m (Test Level 3)

Output1 kV (Test Level 2 - symmetr...

Pulse-shape magnetic field-

Asymmetrical conducted disturbance variables-

Test level 6-

Signals (test level 1)-

UNSPSC 13.239121004

Installation distance right/left-

Ambient temperature (start-up type tested)-40 °C

Max. permissible relative humidity (operation)≤ 95 % (at 25 °C, non-conden...

Input voltage range3x 320 V AC ... 575 V AC

Nominal input voltage range3x 400 V AC ... 500 V AC

Inrush current< 20 A (typical)

Type of protectionTransient surge protection

Setting range of the output voltage (USet)30 V DC ... 56 V DC (> 48 V ...

Derating60 °C ... 70 °C (2.5%/K)

Control deviation< 1 % (change in load, stati...

Power loss nominal load max.70 W

Insulation voltage output / PE500 V DC (routine test)

Mounting positionhorizontal DIN rail NS 35, E...

HART FSK Physical Layer Test Specification Compliance-

Standard - Safe isolationDIN VDE 0100-410

Rail applicationsEN 50121-4

Noise emission-

Input2 kV (Test Level 3 - symmetr...

Frequency-

Number of periods-

Test level 3-

Input, output (test level 3)-

Criterion BTemporary impairment to oper...

ECLASS 5.027242200

UNSPSC 18.039121004

Power frequency magnetic field-

Damped oscillating magnetic field-

Test level 2-

Input, output (test level 1)-

Criterion ANormal operating behavior wi...

Criterion C-

UNSPSC 19.039121004

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installationsEN 50178/VDE 0160 (PELV)

ECLASS 4.027040700

POWER BOOST (IBoost)22.5 A (-25 °C ... 40 °C per...

Active current limitationApprox. IBOOST = 22.5 A (for...

ECLASS 4.127040700

ETIM 4.0EC002540

UNSPSC 12.0139121004

Standard - Approval for medical useIEC 60601-1, 2 x MOOP

ETIM 3.0EC001039

UNSPSC 6.0130211502

Standard - Equipment safetyBG (design tested)

Frequency range DC0 Hz

Screw threadM3

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipmentEN 50178

UNSPSC 1139121004

UNSPSC 7.090139121004

Ambient temperature (storage/transport)-40 °C ... 85 °C

Electromagnetic compatibilityConformance with EMC Directi...

Colorgray

Interface 1Ethernet interface, 10/100/1...

Depth86 mm

External cable diameter5.5 mm ... 6.5 mm

Supply voltage range36 V DC ... 52 V DC 10 % (v...

Connection methodRJ45 jack

Switch-on threshold≥ 30 mA

Local diagnosticsYellow LED

HumidityB

Type of testContinuous shock according t...

Height101.3 mm

Altitude≤ 5000 m (For restrictions, ...

Electrical isolationFE // Ethernet

Signal± 1 kV (Data line, asymmetri...

ECLASS 11.019170112

Net weight124.2 g

Degree of pollution2

ETIM 6.0EC002599

Conductor cross section AWG min.26

Conductor cross section flexible max.1.5 mm²

Frequency range0.15 MHz ... 80 MHz

DesignationShipbuilding

Power consumption270 mW (Shield current monit...

Additional textPlease follow the special in...

Width23.8 mm

EMCB

Ambient temperature (operation)-40 °C ... 75 °C

Degree of protectionIP20 (Manufacturer's declara...

Indirect discharge± 6 kV

ECLASS 7.019170112

Housing materialPlastic

Overvoltage categoryII

REACh SVHCLead 7439-92-1

Note on the connection methodCAT5e

Stripping length8 mm

Serial transmission speed10/100/1000 Mbps

Current carrying capacity≤ 1.5 A (≤ 60 W (PoE+))

Mounting typeDIN rail mounting, stationar...

MTTF3281 Years (SN 29500 standar...

Transmission length100 m (including patch cable...

China RoHSEnvironmentally Friendly Use...

IdentificationDNV GL

Standards/regulationsDIN EN 61643-21

IEC test classificationC2

ECLASS 9.019170112

Utilization restrictionEMC: class A product, see ma...

Permissible humidity (operation)10 % ... 95 % (non-condensin...

Conductor cross section flexible min.0.2 mm²

Conductor cross section AWG max.16

Voltage≤ 10 V

ECLASS 6.019170100

Conductor cross section, flexible, with ferrule, with plastic sleeve0.25 mm² ... 1.5 mm² (only t...

Interface 2Ethernet interface, 10/100/1...

VibrationB

Test result10g for 16 ms, 1000 shocks i...

Rated insulation voltage85 V DC

Response time3 s

Contact discharge± 6 kV (Test Level 3)

Conductor cross section solid max.1.5 mm²

TemperatureD

ETIM 7.0EC002599

CommentsCriterion B

Conductor cross section flexible, with ferrule without plastic sleeve0.25 mm² ... 1.5 mm² (only t...

ECLASS 10.0.119170112

Pin assignment1:1

Maximum output power60 W

Precision± 5 %

Continuous shield current≤ 1.5 A

CertificateCSA 22.2 No. 60079-0 Ed. 3 /...

Conductor cross section solid min.0.2 mm²

Impedance≤ 1 Ω

Maximum output current725 mA (PoE)

Width with alternative assembly-

Climatic class-

AC frequency range-

Mains buffering time-

Nominal output voltage-

Connection in parallel-

Connection in series-

Typical response time-

Environmental protection directive-

Protection class-

Low Voltage Directive-

Flicker-

I/O/S-

Installation distance top/bottom-

Current consumption-

Protective circuit/component-

Dynamic Boost (IDyn.Boost)-

Selective Fuse Breaking (ISFB)-

Output power-

MTBF (IEC 61709, SN 29500)-

Assembly instructions-

EMC requirements for noise emission-

Standard - Safety of transformers-

Standard - safety for equipment for measurement, control, and laboratory use-

Standard – Limitation of mains harmonic currents-

Mains variation/undervoltage-

CSA-

SIQ-

DNV GL noise radiation-

Discharge in air-

Fast transients (burst)-

Conducted interference-

Voltage dips-

Attenuated sinusoidal oscillations (ring wave)-

Test level 4-

Attenuated oscillating wave-

ECLASS 5.1-

UNSPSC 21.0-

Depth with alternative assembly-

Installation height-

Frequency range (fN)-

Nominal power consumption-

Recommended breaker for input protection-

Nominal output current (IN)-

Protection against overvoltage at the output (OVP)-

Residual ripple-

Insulation voltage input/output-

EMC requirements for noise immunity-

Standard – Safety extra-low voltage-

UL approvals-

Shipbuilding approval-

Harmonic currents-

Electrostatic discharge-

Electromagnetic HF field-

Surge voltage load (surge)-

Voltage dip-

Test level 1-

Test level 5-

Input, output (test level 2)-

Signals (test level 2)-

UNSPSC 20.0-

Height with alternative assembly-

Inflammability class in acc. with UL 94 (housing / terminal blocks)-

Discharge current to PE-

Power factor (cos phi)-

Static Boost (IStat.Boost)-

Feedback voltage resistance-

Maximum power dissipation in no-load condition-

Efficiency-

Insulation voltage input / PE-

EMC requirements, power plant-

Standard - Electrical safety-

Standard - power supply devices for low voltage with DC output-

Conducted noise emission-

DNV GL conducted interference-

Test field strength-

Output-

Pulse-shape magnetic field-

Asymmetrical conducted disturbance variables-

Test level 6-

Signals (test level 1)-

UNSPSC 13.2-

Installation distance right/left-

Ambient temperature (start-up type tested)-

Max. permissible relative humidity (operation)-

Input voltage range-

Nominal input voltage range-

Inrush current-

Type of protection-

Setting range of the output voltage (USet)-

Derating-

Control deviation-

Power loss nominal load max.-

Insulation voltage output / PE-

Mounting position-

HART FSK Physical Layer Test Specification Compliance-

Standard - Safe isolation-

Rail applications-

Noise emission-

Input-

Frequency-

Number of periods-

Test level 3-

Input, output (test level 3)-

Criterion B-

ECLASS 5.0-

UNSPSC 18.0-

Power frequency magnetic field-

Damped oscillating magnetic field-

Test level 2-

Input, output (test level 1)-

Criterion A-

Criterion C-

UNSPSC 19.0-

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

ECLASS 4.0-

POWER BOOST (IBoost)-

Active current limitation-

ECLASS 4.1-

ETIM 4.0-

UNSPSC 12.01-

Standard - Approval for medical use-

ETIM 3.0-

UNSPSC 6.01-

Standard - Equipment safety-

Frequency range DC-

Screw thread-

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment-

UNSPSC 11-

UNSPSC 7.0901-