2316149 Phoenix Contact Data & Networking Devices

Ambient temperature (operation)-25 °C ... 70 °C (> 60 °C De...

Fieldbus Foundation-

Conductor cross section AWG max.16

Max. output voltage Uo-

ATEX-

ECLASS 7.027049002

ETIM 7.0EC002540

ECLASS 5.127242200

Depth125 mm

Net weight1.1 kg

Connection methodPush-in connection

Standards/regulations-

ECLASS 10.0.127040701

ETIM 4.0-

Height130 mm

Permissible humidity (operation)-

Conductor cross section flexible min.0.2 mm²

Conductor cross section solid min.0.2 mm²

Conductor cross section AWG min.24

Type of test-

IECEx-

ETIM 6.0EC002540

ECLASS 9.027040701

Width70 mm

Ambient temperature (storage/transport)-40 °C ... 85 °C

Conductor cross section flexible max.1.5 mm²

Conductor cross section solid max.1 mm²

Interface 1-

Interface-

Output name-

REACh SVHCLead 7439-92-1

CSA, USA/Canada-

Utilization restriction-

Conformance-

Number of connections-

Inductance Li-

Designation-

China RoHSEnvironmentally Friendly Use...

ECLASS 11.027040701

ECLASS 6.027049000

Degree of protectionIP20

Ambient temperature (start-up type tested)-40 °C

Degree of pollution2

Discharge current to PE< 3.5 mA

Mains buffering timetyp. 33 ms (3x 400 V AC)

Protective circuit/componentVaristor, gas-filled surge a...

Connection in parallelYes, for redundancy and incr...

Output power480 W

MTBF (IEC 61709, SN 29500)> 985000 h (25 °C)

Insulation voltage output / PE0.5 kV DC (type test)

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

UL approvalsUL Listed UL 508

Contact discharge8 kV (Test Level 4)

Test field strength110 A/m

Input2 kV (Test Level 4 - symmetr...

Criterion BTemporary impairment to oper...

ECLASS 4.0-

Max. permissible relative humidity (operation)≤ 95 % (at 25 °C, non-conden...

Input voltage range3x 400 V AC ... 500 V AC -20...

AC frequency range50 Hz ... 60 Hz -10 % ... +1...

Recommended breaker for input protection3x 4 A ... 20 A (Characteris...

POWER BOOST (IBoost)-

Connection in seriesyes

Active current limitation-

Typical response time300 ms (from SLEEP MODE)

Housing material-

Assembly instructionsalignable: PN ≥50%, 5 mm hor...

Standard - Safety of transformersIEC 61558-2-16 pending

Standard – Limitation of mains harmonic currentsEN 61000-3-2

Electromagnetic HF fieldEN 61000-4-3

Signal1 kV (Test Level 2 - asymmet...

Criterion ANormal operating behavior wi...

ECLASS 4.1-

UNSPSC 12.01-

Width with alternative assembly122 mm

Installation height≤ 5000 m (> 2000 m, observe ...

Nominal power consumption541 VA

Nominal output current (IN)20 A

Selective Fuse Breaking (ISFB)120 A (15 ms)

Protection against overvoltage at the output (OVP)≤ 32 V DC

Insulation voltage input / PE3.5 kV AC (type test)

Mounting positionhorizontal DIN rail NS 35, E...

Stripping length8 mm

EMC requirements for noise emissionEN 61000-6-3

Standard – Safety extra-low voltageIEC 61010-1 (SELV)

Standard - Approval for medical use-

CSACAN/CSA-C22.2 No. 60950-1-07

Electrostatic dischargeEN 61000-4-2

Low Voltage DirectiveConformance with Low Voltage...

Fast transients (burst)EN 61000-4-4

Output1 kV (Test Level 3 - symmetr...

Voltage2.5 kV

ECLASS 5.027242200

ETIM 3.0-

UNSPSC 6.01-

UNSPSC 20.039121004

Height with alternative assembly130 mm

Climatic class3K3 (in acc. with EN 60721)

Current consumption3x 0.99 A (400 V AC)

Type of protectionTransient surge protection

Setting range of the output voltage (USet)24 V DC ... 29.5 V DC (const...

Feedback voltage resistance≤ 35 V DC

Residual ripple< 60 mVPP (with nominal valu...

Power loss nominal load max.< 32 W (400 V AC)

Insulation voltage input/output4 kV AC (type test)

Protection classI

EMC requirements for noise immunityEN 61000-6-1

Standard - Electrical safetyIEC 61010-2-201 (SELV)

Standard - Equipment safety-

Standard - Safe isolationIEC 61558-2-16 pending

Electromagnetic compatibilityConformance with EMC Directi...

Frequency range50 Hz ... 60 Hz

Surge voltage load (surge)EN 61000-4-5

Conducted interferenceEN 61000-4-6

UNSPSC 21.039121004

Depth with alternative assembly73 mm

Nominal input voltage range3x 400 V AC ... 500 V AC

Frequency range DC-

Inrush currenttyp. 2 A (at 25 °C)

Nominal output voltage24 V DC

Derating> 60 °C ... 70 °C (2.5%/K)

Control deviation< 0.5 % (Static load change ...

Maximum power dissipation in no-load condition< 7 W (400 V AC)

Efficiencytyp. 93.9 % (400 V AC)

Screw thread-

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment-

Rail applicationsEN 50121-3-2

Discharge in air15 kV (Test Level 4)

CommentsCriterion A

I/O/Sasymmetrical

UNSPSC 11-

UNSPSC 18.039121004

UNSPSC 7.0901-

UNSPSC 13.239121004

UNSPSC 19.039121004

Environmental protection directiveRoHS Directive 2011/65/EU

FlickerEN 61000-3-3

Installation distance top/bottom50 mm / 50 mm

Dynamic Boost (IDyn.Boost)30 A (5 s)

Standard - safety for equipment for measurement, control, and laboratory useIEC 61010-1

Mains variation/undervoltageSEMI F47-0706, EN 61000-4-11

SIQBG (type approved)

DNV GL noise radiationClass B

Voltage dipsEN 61000-4-11

Attenuated sinusoidal oscillations (ring wave)EN 61000-4-12

Test level 415 kHz 150 kHz (Test Level 4...

Attenuated oscillating waveEN 61000-4-18

Frequency range (fN)50 Hz ... 60 Hz -10 % ... +1...

Shipbuilding approvalDNV GL, PRS, BV, LR, ABS

Harmonic currentsEN 61000-3-2

Voltage dip0 %

Test level 115 Hz 150 Hz (Test Level 4)

Test level 516.7 Hz 50 Hz 60 Hz (Test Le...

Input, output (test level 2)10 MHz

Signals (test level 2)100 kHz 1 MHz (Test Level 3 ...

Inflammability class in acc. with UL 94 (housing / terminal blocks)V0

Power factor (cos phi)0.94

Static Boost (IStat.Boost)25 A

EMC requirements, power plantIEC 61850-3

Standard - power supply devices for low voltage with DC outputEN 61204-3

Conducted noise emissionEN 55016

DNV GL conducted interferenceClass A

Pulse-shape magnetic fieldEN 61000-4-9

Asymmetrical conducted disturbance variablesEN 61000-4-16

Test level 616.7 Hz 50 Hz 60 Hz (Test Le...

Signals (test level 1)100 kHz 1 MHz (Test Level 3 ...

Installation distance right/left5 mm / 5 mm

HART FSK Physical Layer Test Specification ComplianceOutput voltage UOut complian...

Noise emissionEN 55016

Additional textTest Level 2

Frequency50 Hz

Number of periods0,5 / 1 / 5 / 50 / 250 perio...

Test level 31.5 kHz 15 kHz (Test Level 4...

Input, output (test level 3)100 kHz 1 MHz (Test Level 3 ...

Power frequency magnetic fieldEN 61000-4-8

Damped oscillating magnetic fieldEN 61000-4-10

Test level 2150 Hz 1.5 kHz (Test Level 4...

Input, output (test level 1)100 kHz 1 MHz (Test Level 3 ...

Criterion CTemporary adverse effects on...

Ambient temperature (operation)-40 °C ... 70 °C

Fieldbus FoundationFF-831

Conductor cross section AWG max.12

Max. output voltage Uo30 V DC (trunk and host)

ATEXSira 11ATEX4216X; II 3 G Ex ...

ECLASS 7.027242611

ETIM 7.0EC002584

ECLASS 5.127242600

Depth180 mm

Net weight222.222 g

Connection method37-pin to 25-pin Invensys® D...

Standards/regulationsShock and vibration in acc. ...

ECLASS 10.0.127242692

ETIM 4.0EC002583

Height77 mm

Permissible humidity (operation)95 % (non-condensing)

Conductor cross section flexible min.0.20 mm²

Conductor cross section solid min.0.20 mm²

Conductor cross section AWG min.30

Type of testCorrosive resistance in acc....

IECExIECEx SIR 11.0097X; Ex nA nC...

ETIM 6.0EC002584

ECLASS 9.027242692

Width180 mm

Ambient temperature (storage/transport)-40 °C ... 85 °C

Conductor cross section flexible max.2.50 mm²

Conductor cross section solid max.2.50 mm²

Interface 1Generic host system cabling

InterfaceHost system

Output nameAlarm

REACh SVHCLead 7439-92-1

CSA, USA/CanadaClass I, Div. 2, Groups A, B...

Utilization restrictionEMC: class A product, see ma...

ConformanceCE-compliant

Number of connections1

Inductance Li17.8 mH (trunk and host)

DesignationStandards/regulations

China RoHSEnvironmentally Friendly Use...

ECLASS 11.027242692

ECLASS 6.027242600

Degree of protectionIP20

Ambient temperature (start-up type tested)-

Degree of pollution-

Discharge current to PE-

Mains buffering time-

Protective circuit/component-

Connection in parallel-

Output power-

MTBF (IEC 61709, SN 29500)-

Insulation voltage output / PE-

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

UL approvals-

Contact discharge-

Test field strength-

Input-

Criterion B-

ECLASS 4.0-

Max. permissible relative humidity (operation)-

Input voltage range-

AC frequency range-

Recommended breaker for input protection-

POWER BOOST (IBoost)-

Connection in series-

Active current limitation-

Typical response time-

Housing material-

Assembly instructions-

Standard - Safety of transformers-

Standard – Limitation of mains harmonic currents-

Electromagnetic HF field-

Signal-

Criterion A-

ECLASS 4.1-

UNSPSC 12.01-

Width with alternative assembly-

Installation height-

Nominal power consumption-

Nominal output current (IN)-

Selective Fuse Breaking (ISFB)-

Protection against overvoltage at the output (OVP)-

Insulation voltage input / PE-

Mounting position-

Stripping length-

EMC requirements for noise emission-

Standard – Safety extra-low voltage-

Standard - Approval for medical use-

CSA-

Electrostatic discharge-

Low Voltage Directive-

Fast transients (burst)-

Output-

Voltage-

ECLASS 5.0-

ETIM 3.0-

UNSPSC 6.01-

UNSPSC 20.0-

Height with alternative assembly-

Climatic class-

Current consumption-

Type of protection-

Setting range of the output voltage (USet)-

Feedback voltage resistance-

Residual ripple-

Power loss nominal load max.-

Insulation voltage input/output-

Protection class-

EMC requirements for noise immunity-

Standard - Electrical safety-

Standard - Equipment safety-

Standard - Safe isolation-

Electromagnetic compatibility-

Frequency range-

Surge voltage load (surge)-

Conducted interference-

UNSPSC 21.0-

Depth with alternative assembly-

Nominal input voltage range-

Frequency range DC-

Inrush current-

Nominal output voltage-

Derating-

Control deviation-

Maximum power dissipation in no-load condition-

Efficiency-

Screw thread-

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment-

Rail applications-

Discharge in air-

Comments-

I/O/S-

UNSPSC 11-

UNSPSC 18.0-

UNSPSC 7.0901-

UNSPSC 13.2-

UNSPSC 19.0-

Environmental protection directive-

Flicker-

Installation distance top/bottom-

Dynamic Boost (IDyn.Boost)-

Standard - safety for equipment for measurement, control, and laboratory use-

Mains variation/undervoltage-

SIQ-

DNV GL noise radiation-

Voltage dips-

Attenuated sinusoidal oscillations (ring wave)-

Test level 4-

Attenuated oscillating wave-

Frequency range (fN)-

Shipbuilding approval-

Harmonic currents-

Voltage dip-

Test level 1-

Test level 5-

Input, output (test level 2)-

Signals (test level 2)-

Inflammability class in acc. with UL 94 (housing / terminal blocks)-

Power factor (cos phi)-

Static Boost (IStat.Boost)-

EMC requirements, power plant-

Standard - power supply devices for low voltage with DC output-

Conducted noise emission-

DNV GL conducted interference-

Pulse-shape magnetic field-

Asymmetrical conducted disturbance variables-

Test level 6-

Signals (test level 1)-

Installation distance right/left-

HART FSK Physical Layer Test Specification Compliance-

Noise emission-

Additional text-

Frequency-

Number of periods-

Test level 3-

Input, output (test level 3)-

Power frequency magnetic field-

Damped oscillating magnetic field-

Test level 2-

Input, output (test level 1)-

Criterion C-

Ambient temperature (operation)-25 °C ... 70 °C (> 60 °C De...

Fieldbus Foundation-

Conductor cross section AWG max.10

Max. output voltage Uo-

ATEX-

ECLASS 7.027049002

ETIM 7.0EC002540

ECLASS 5.127242200

Depth179 mm

Net weight2.5 kg

Connection methodScrew connection

Standards/regulations-

ECLASS 10.0.127040701

ETIM 4.0EC002540

Height130 mm

Permissible humidity (operation)-

Conductor cross section flexible min.0.2 mm²

Conductor cross section solid min.0.2 mm²

Conductor cross section AWG min.18

Type of test-

IECEx-

ETIM 6.0EC002540

ECLASS 9.027040701

Width96 mm

Ambient temperature (storage/transport)-40 °C ... 85 °C

Conductor cross section flexible max.4 mm²

Conductor cross section solid max.6 mm²

Interface 1-

Interface-

Output name-

REACh SVHCLead 7439-92-1

CSA, USA/Canada-

Utilization restriction-

Conformance-

Number of connections-

Inductance Li-

Designation-

China RoHSEnvironmentally Friendly Use...

ECLASS 11.027040701

ECLASS 6.027049000

Degree of protectionIP20

Ambient temperature (start-up type tested)-40 °C

Degree of pollution2

Discharge current to PE< 3.5 mA

Mains buffering timetyp. 25 ms (400 V AC)

Protective circuit/componentVaristor

Connection in parallelYes, for redundancy and incr...

Output power960 W

MTBF (IEC 61709, SN 29500)> 890000 h (25 °C)

Insulation voltage output / PE500 V DC (routine test)

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installationsEN 50178/VDE 0160 (PELV)

UL approvalsUL Listed UL 508

Contact discharge8 kV (Test Level 4)

Test field strength10 V/m (Test Level 3)

Input2 kV (Test Level 3 - symmetr...

Criterion BTemporary impairment to oper...

ECLASS 4.027040700

Max. permissible relative humidity (operation)≤ 95 % (at 25 °C, non-conden...

Input voltage range3x 320 V AC ... 575 V AC

AC frequency range45 Hz ... 65 Hz

Recommended breaker for input protection6 A ... 16 A (AC: Characteri...

POWER BOOST (IBoost)22.5 A (-25 °C ... 40 °C per...

Connection in seriesyes

Active current limitationApprox. IBOOST = 22.5 A (for...

Typical response time< 1 s

Housing materialSteel sheet, zinc-plated

Assembly instructionsalignable: PN ≥50%, 5 mm hor...

Standard - Safety of transformersIEC 61558-2-17

Standard – Limitation of mains harmonic currentsEN 61000-3-2

Electromagnetic HF fieldEN 61000-4-3

Signal1 kV (Test Level 2 - asymmet...

Criterion ANormal operating behavior wi...

ECLASS 4.127040700

UNSPSC 12.0139121004

Width with alternative assembly176 mm

Installation height4000 m

Nominal power consumption1386 VA

Nominal output current (IN)20 A (-25 °C ... 60 °C, UOUT...

Selective Fuse Breaking (ISFB)100 A (12 ms)

Protection against overvoltage at the output (OVP)< 60 V DC

Insulation voltage input / PE3.5 kV AC (type test)

Mounting positionhorizontal DIN rail NS 35, E...

Stripping length10 mm

EMC requirements for noise emissionEN 61000-6-3

Standard – Safety extra-low voltageIEC 60950-1 (SELV) and EN 60...

Standard - Approval for medical useIEC 60601-1, 2 x MOOP

CSACAN/CSA-C22.2 No. 60950-1-07

Electrostatic dischargeEN 61000-4-2

Low Voltage DirectiveConformance with Low Voltage...

Fast transients (burst)EN 61000-4-4

Output1 kV (Test Level 2 - symmetr...

Voltage10 V (Test Level 3)

ECLASS 5.027242200

ETIM 3.0EC001039

UNSPSC 6.0130211502

UNSPSC 20.039121004

Height with alternative assembly130 mm

Climatic class3K3 (in acc. with EN 60721)

Current consumption3x 2.1 A (400 V AC)

Type of protectionTransient surge protection

Setting range of the output voltage (USet)30 V DC ... 56 V DC (> 48 V ...

Feedback voltage resistancemax. 60 V DC

Residual ripple< 50 mVPP (with nominal valu...

Power loss nominal load max.70 W

Insulation voltage input/output4 kV AC (type test)

Protection classI

EMC requirements for noise immunityEN 61000-6-1

Standard - Electrical safetyIEC 60950-1/VDE 0805 (SELV)

Standard - Equipment safetyBG (design tested)

Standard - Safe isolationDIN VDE 0100-410

Electromagnetic compatibilityConformance with EMC Directi...

Frequency range0.15 MHz ... 80 MHz

Surge voltage load (surge)EN 61000-4-5

Conducted interferenceEN 61000-4-6

UNSPSC 21.039121004

Depth with alternative assembly99 mm

Nominal input voltage range3x 400 V AC ... 500 V AC

Frequency range DC0 Hz

Inrush current< 20 A (typical)

Nominal output voltage48 V DC ±1 %

Derating60 °C ... 70 °C (2.5%/K)

Control deviation< 1 % (change in load, stati...

Maximum power dissipation in no-load condition24 W

Efficiency> 93 % (at 400 V AC and nomi...

Screw threadM3

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipmentEN 50178

Rail applicationsEN 50121-4

Discharge in air15 kV (Test Level 4)

CommentsCriterion A

I/O/Sasymmetrical

UNSPSC 1139121004

UNSPSC 18.039121004

UNSPSC 7.090139121004

UNSPSC 13.239121004

UNSPSC 19.039121004

Environmental protection directive-

Flicker-

Installation distance top/bottom-

Dynamic Boost (IDyn.Boost)-

Standard - safety for equipment for measurement, control, and laboratory use-

Mains variation/undervoltage-

SIQ-

DNV GL noise radiation-

Voltage dips-

Attenuated sinusoidal oscillations (ring wave)-

Test level 4-

Attenuated oscillating wave-

Frequency range (fN)-

Shipbuilding approval-

Harmonic currents-

Voltage dip-

Test level 1-

Test level 5-

Input, output (test level 2)-

Signals (test level 2)-

Inflammability class in acc. with UL 94 (housing / terminal blocks)-

Power factor (cos phi)-

Static Boost (IStat.Boost)-

EMC requirements, power plant-

Standard - power supply devices for low voltage with DC output-

Conducted noise emission-

DNV GL conducted interference-

Pulse-shape magnetic field-

Asymmetrical conducted disturbance variables-

Test level 6-

Signals (test level 1)-

Installation distance right/left-

HART FSK Physical Layer Test Specification Compliance-

Noise emission-

Additional text-

Frequency-

Number of periods-

Test level 3-

Input, output (test level 3)-

Power frequency magnetic field-

Damped oscillating magnetic field-

Test level 2-

Input, output (test level 1)-

Criterion C-

Ambient temperature (operation)-25 °C ... 70 °C (> 60 °C De...

Fieldbus Foundation-

Conductor cross section AWG max.16

Max. output voltage Uo-

ATEX-

ECLASS 7.027049002

ETIM 7.0EC002540

ECLASS 5.127242200

Depth125 mm

Net weight1.1 kg

Connection methodPush-in connection

Standards/regulations-

ECLASS 10.0.127040701

ETIM 4.0-

Height130 mm

Permissible humidity (operation)-

Conductor cross section flexible min.0.2 mm²

Conductor cross section solid min.0.2 mm²

Conductor cross section AWG min.24

Type of test-

IECEx-

ETIM 6.0EC002540

ECLASS 9.027040701

Width70 mm

Ambient temperature (storage/transport)-40 °C ... 85 °C

Conductor cross section flexible max.1.5 mm²

Conductor cross section solid max.1 mm²

Interface 1-

Interface-

Output name-

REACh SVHCLead 7439-92-1

CSA, USA/Canada-

Utilization restriction-

Conformance-

Number of connections-

Inductance Li-

Designation-

China RoHSEnvironmentally Friendly Use...

ECLASS 11.027040701

ECLASS 6.027049000

Degree of protectionIP20

Ambient temperature (start-up type tested)-40 °C

Degree of pollution2

Discharge current to PE< 3.5 mA

Mains buffering timetyp. 33 ms (3x 400 V AC)

Protective circuit/componentVaristor, gas-filled surge a...

Connection in parallelYes, for redundancy and incr...

Output power480 W

MTBF (IEC 61709, SN 29500)> 985000 h (25 °C)

Insulation voltage output / PE0.5 kV DC (type test)

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

UL approvalsUL Listed UL 508

Contact discharge8 kV (Test Level 4)

Test field strength110 A/m

Input2 kV (Test Level 4 - symmetr...

Criterion BTemporary impairment to oper...

ECLASS 4.0-

Max. permissible relative humidity (operation)≤ 95 % (at 25 °C, non-conden...

Input voltage range3x 400 V AC ... 500 V AC -20...

AC frequency range50 Hz ... 60 Hz -10 % ... +1...

Recommended breaker for input protection3x 4 A ... 20 A (Characteris...

POWER BOOST (IBoost)-

Connection in seriesyes

Active current limitation-

Typical response time300 ms (from SLEEP MODE)

Housing material-

Assembly instructionsalignable: PN ≥50%, 5 mm hor...

Standard - Safety of transformersIEC 61558-2-16 pending

Standard – Limitation of mains harmonic currentsEN 61000-3-2

Electromagnetic HF fieldEN 61000-4-3

Signal1 kV (Test Level 2 - asymmet...

Criterion ANormal operating behavior wi...

ECLASS 4.1-

UNSPSC 12.01-

Width with alternative assembly122 mm

Installation height≤ 5000 m (> 2000 m, observe ...

Nominal power consumption541 VA

Nominal output current (IN)20 A

Selective Fuse Breaking (ISFB)120 A (15 ms)

Protection against overvoltage at the output (OVP)≤ 32 V DC

Insulation voltage input / PE3.5 kV AC (type test)

Mounting positionhorizontal DIN rail NS 35, E...

Stripping length8 mm

EMC requirements for noise emissionEN 61000-6-3

Standard – Safety extra-low voltageIEC 61010-1 (SELV)

Standard - Approval for medical use-

CSACAN/CSA-C22.2 No. 60950-1-07

Electrostatic dischargeEN 61000-4-2

Low Voltage DirectiveConformance with Low Voltage...

Fast transients (burst)EN 61000-4-4

Output1 kV (Test Level 3 - symmetr...

Voltage2.5 kV

ECLASS 5.027242200

ETIM 3.0-

UNSPSC 6.01-

UNSPSC 20.039121004

Height with alternative assembly130 mm

Climatic class3K3 (in acc. with EN 60721)

Current consumption3x 0.99 A (400 V AC)

Type of protectionTransient surge protection

Setting range of the output voltage (USet)24 V DC ... 29.5 V DC (const...

Feedback voltage resistance≤ 35 V DC

Residual ripple< 60 mVPP (with nominal valu...

Power loss nominal load max.< 32 W (400 V AC)

Insulation voltage input/output4 kV AC (type test)

Protection classI

EMC requirements for noise immunityEN 61000-6-1

Standard - Electrical safetyIEC 61010-2-201 (SELV)

Standard - Equipment safety-

Standard - Safe isolationIEC 61558-2-16 pending

Electromagnetic compatibilityConformance with EMC Directi...

Frequency range50 Hz ... 60 Hz

Surge voltage load (surge)EN 61000-4-5

Conducted interferenceEN 61000-4-6

UNSPSC 21.039121004

Depth with alternative assembly73 mm

Nominal input voltage range3x 400 V AC ... 500 V AC

Frequency range DC-

Inrush currenttyp. 2 A (at 25 °C)

Nominal output voltage24 V DC

Derating> 60 °C ... 70 °C (2.5%/K)

Control deviation< 0.5 % (Static load change ...

Maximum power dissipation in no-load condition< 7 W (400 V AC)

Efficiencytyp. 93.9 % (400 V AC)

Screw thread-

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment-

Rail applicationsEN 50121-3-2

Discharge in air15 kV (Test Level 4)

CommentsCriterion A

I/O/Sasymmetrical

UNSPSC 11-

UNSPSC 18.039121004

UNSPSC 7.0901-

UNSPSC 13.239121004

UNSPSC 19.039121004

Environmental protection directiveRoHS Directive 2011/65/EU

FlickerEN 61000-3-3

Installation distance top/bottom50 mm / 50 mm

Dynamic Boost (IDyn.Boost)30 A (5 s)

Standard - safety for equipment for measurement, control, and laboratory useIEC 61010-1

Mains variation/undervoltageSEMI F47-0706, EN 61000-4-11

SIQBG (type approved)

DNV GL noise radiationClass B

Voltage dipsEN 61000-4-11

Attenuated sinusoidal oscillations (ring wave)EN 61000-4-12

Test level 415 kHz 150 kHz (Test Level 4...

Attenuated oscillating waveEN 61000-4-18

Frequency range (fN)50 Hz ... 60 Hz -10 % ... +1...

Shipbuilding approvalDNV GL, PRS, BV, LR, ABS

Harmonic currentsEN 61000-3-2

Voltage dip0 %

Test level 115 Hz 150 Hz (Test Level 4)

Test level 516.7 Hz 50 Hz 60 Hz (Test Le...

Input, output (test level 2)10 MHz

Signals (test level 2)100 kHz 1 MHz (Test Level 3 ...

Inflammability class in acc. with UL 94 (housing / terminal blocks)V0

Power factor (cos phi)0.94

Static Boost (IStat.Boost)25 A

EMC requirements, power plantIEC 61850-3

Standard - power supply devices for low voltage with DC outputEN 61204-3

Conducted noise emissionEN 55016

DNV GL conducted interferenceClass A

Pulse-shape magnetic fieldEN 61000-4-9

Asymmetrical conducted disturbance variablesEN 61000-4-16

Test level 616.7 Hz 50 Hz 60 Hz (Test Le...

Signals (test level 1)100 kHz 1 MHz (Test Level 3 ...

Installation distance right/left5 mm / 5 mm

HART FSK Physical Layer Test Specification ComplianceOutput voltage UOut complian...

Noise emissionEN 55016

Additional textTest Level 2

Frequency50 Hz

Number of periods0,5 / 1 / 5 / 50 / 250 perio...

Test level 31.5 kHz 15 kHz (Test Level 4...

Input, output (test level 3)100 kHz 1 MHz (Test Level 3 ...

Power frequency magnetic fieldEN 61000-4-8

Damped oscillating magnetic fieldEN 61000-4-10

Test level 2150 Hz 1.5 kHz (Test Level 4...

Input, output (test level 1)100 kHz 1 MHz (Test Level 3 ...

Criterion CTemporary adverse effects on...

Ambient temperature (operation)-40 °C ... 70 °C

Fieldbus FoundationFF-831

Conductor cross section AWG max.12

Max. output voltage Uo30 V DC (trunk and host)

ATEXSira 11ATEX4216X; II 3 G Ex ...

ECLASS 7.027242611

ETIM 7.0EC002584

ECLASS 5.127242600

Depth180 mm

Net weight222.222 g

Connection method37-pin to 25-pin Invensys® D...

Standards/regulationsShock and vibration in acc. ...

ECLASS 10.0.127242692

ETIM 4.0EC002583

Height77 mm

Permissible humidity (operation)95 % (non-condensing)

Conductor cross section flexible min.0.20 mm²

Conductor cross section solid min.0.20 mm²

Conductor cross section AWG min.30

Type of testCorrosive resistance in acc....

IECExIECEx SIR 11.0097X; Ex nA nC...

ETIM 6.0EC002584

ECLASS 9.027242692

Width180 mm

Ambient temperature (storage/transport)-40 °C ... 85 °C

Conductor cross section flexible max.2.50 mm²

Conductor cross section solid max.2.50 mm²

Interface 1Generic host system cabling

InterfaceHost system

Output nameAlarm

REACh SVHCLead 7439-92-1

CSA, USA/CanadaClass I, Div. 2, Groups A, B...

Utilization restrictionEMC: class A product, see ma...

ConformanceCE-compliant

Number of connections1

Inductance Li17.8 mH (trunk and host)

DesignationStandards/regulations

China RoHSEnvironmentally Friendly Use...

ECLASS 11.027242692

ECLASS 6.027242600

Degree of protectionIP20

Ambient temperature (start-up type tested)-

Degree of pollution-

Discharge current to PE-

Mains buffering time-

Protective circuit/component-

Connection in parallel-

Output power-

MTBF (IEC 61709, SN 29500)-

Insulation voltage output / PE-

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

UL approvals-

Contact discharge-

Test field strength-

Input-

Criterion B-

ECLASS 4.0-

Max. permissible relative humidity (operation)-

Input voltage range-

AC frequency range-

Recommended breaker for input protection-

POWER BOOST (IBoost)-

Connection in series-

Active current limitation-

Typical response time-

Housing material-

Assembly instructions-

Standard - Safety of transformers-

Standard – Limitation of mains harmonic currents-

Electromagnetic HF field-

Signal-

Criterion A-

ECLASS 4.1-

UNSPSC 12.01-

Width with alternative assembly-

Installation height-

Nominal power consumption-

Nominal output current (IN)-

Selective Fuse Breaking (ISFB)-

Protection against overvoltage at the output (OVP)-

Insulation voltage input / PE-

Mounting position-

Stripping length-

EMC requirements for noise emission-

Standard – Safety extra-low voltage-

Standard - Approval for medical use-

CSA-

Electrostatic discharge-

Low Voltage Directive-

Fast transients (burst)-

Output-

Voltage-

ECLASS 5.0-

ETIM 3.0-

UNSPSC 6.01-

UNSPSC 20.0-

Height with alternative assembly-

Climatic class-

Current consumption-

Type of protection-

Setting range of the output voltage (USet)-

Feedback voltage resistance-

Residual ripple-

Power loss nominal load max.-

Insulation voltage input/output-

Protection class-

EMC requirements for noise immunity-

Standard - Electrical safety-

Standard - Equipment safety-

Standard - Safe isolation-

Electromagnetic compatibility-

Frequency range-

Surge voltage load (surge)-

Conducted interference-

UNSPSC 21.0-

Depth with alternative assembly-

Nominal input voltage range-

Frequency range DC-

Inrush current-

Nominal output voltage-

Derating-

Control deviation-

Maximum power dissipation in no-load condition-

Efficiency-

Screw thread-

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment-

Rail applications-

Discharge in air-

Comments-

I/O/S-

UNSPSC 11-

UNSPSC 18.0-

UNSPSC 7.0901-

UNSPSC 13.2-

UNSPSC 19.0-

Environmental protection directive-

Flicker-

Installation distance top/bottom-

Dynamic Boost (IDyn.Boost)-

Standard - safety for equipment for measurement, control, and laboratory use-

Mains variation/undervoltage-

SIQ-

DNV GL noise radiation-

Voltage dips-

Attenuated sinusoidal oscillations (ring wave)-

Test level 4-

Attenuated oscillating wave-

Frequency range (fN)-

Shipbuilding approval-

Harmonic currents-

Voltage dip-

Test level 1-

Test level 5-

Input, output (test level 2)-

Signals (test level 2)-

Inflammability class in acc. with UL 94 (housing / terminal blocks)-

Power factor (cos phi)-

Static Boost (IStat.Boost)-

EMC requirements, power plant-

Standard - power supply devices for low voltage with DC output-

Conducted noise emission-

DNV GL conducted interference-

Pulse-shape magnetic field-

Asymmetrical conducted disturbance variables-

Test level 6-

Signals (test level 1)-

Installation distance right/left-

HART FSK Physical Layer Test Specification Compliance-

Noise emission-

Additional text-

Frequency-

Number of periods-

Test level 3-

Input, output (test level 3)-

Power frequency magnetic field-

Damped oscillating magnetic field-

Test level 2-

Input, output (test level 1)-

Criterion C-