1656990 Phoenix Contact Data & Networking Devices

Weight-

Maximum external conductor diameter-

Ambient temperature (operation)-

Width-

Connection method-

AWG solid max.-

No. of cable outlets-

Degree of pollution-

Conductor cross section-

Ambient temperature (storage/transport)-

Contact surface material-

Rated current-

ECLASS 11.0-

ECLASS 6.0-

AWG solid min.-

Overvoltage category-

AWG multi-stranded max.-

Flammability rating according to UL 94-

Ambient temperature (assembly)-

Housing material-

Nominal voltage UN-

UNSPSC 11-

ECLASS 9.0-

UNSPSC 13.2-

UNSPSC 20.0-

Height-

Length-

ECLASS 4.0-

ETIM 2.0-

ETIM 4.0-

UNSPSC 12.01-

UNSPSC 21.0-

Minimum external conductor diameter-

AWG multi-stranded min.-

Cable outlet-

UNSPSC 6.01-

Contact material-

Number of positions-

UNSPSC 19.0-

GRP transmission properties-

ECLASS 10.0.1-

ECLASS 7.0-

Contact carrier material-

Rated voltage (III/3)-

China RoHS-

Connection in acc. with standard-

Transmission characteristics (category)-

Contact resistance-

ETIM 3.0-

UNSPSC 7.0901-

UNSPSC 18.0-

ETIM 7.0-

ECLASS 4.1-

ECLASS 5.1-

ETIM 6.0-

ECLASS 5.0-

Height-

Degree of protection-

Ambient temperature (operation)-

Max. permissible relative humidity (operation)-

Nominal power consumption-

Mains buffering time-

Protective circuit/component-

Feedback voltage resistance-

Output power-

Depth-

Inflammability class in acc. with UL 94 (housing / terminal blocks)-

Climatic class-

Input voltage range-

Inrush current-

Type of protection-

Width-

Installation distance top/bottom-

Ambient temperature (storage/transport)-

Nominal input voltage range-

Frequency range (fN)-

Input fuse-

Power factor (cos phi)-

Connection in parallel-

Residual ripple-

Control deviation-

Efficiency-

Standard – Safety extra-low voltage-

Discharge in air-

Comments-

Surge voltage load (surge)-

Voltage dips-

ECLASS 10.0.1-

ETIM 6.0-

UNSPSC 11-

UNSPSC 19.0-

Installation distance right/left-

Degree of pollution-

Current consumption-

Recommended breaker for input protection-

Nominal output current (IN)-

Nominal output voltage-

Connection in series-

Net weight-

Protection class-

Assembly instructions-

Conductor cross section AWG min.-

Screw thread-

Standard - Safety of transformers-

Standard – Limitation of mains harmonic currents-

Electromagnetic compatibility-

Contact discharge-

Input-

Criterion A-

ECLASS 4.0-

ECLASS 5.1-

ETIM 3.0-

UNSPSC 12.01-

UNSPSC 21.0-

MTBF (IEC 61709, SN 29500)-

Foot latch material-

Mounting position-

Conductor cross section flexible max.-

EMC requirements for noise immunity-

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

CSA-

Fast transients (burst)-

Electromagnetic HF field-

Output-

China RoHS-

ECLASS 6.0-

ECLASS 7.0-

UNSPSC 7.0901-

UNSPSC 18.0-

ECLASS 5.0-

ECLASS 9.0-

ETIM 7.0-

UNSPSC 20.0-

Derating-

Typical response time-

Housing material-

EMC requirements for noise emission-

Standard - Safe isolation-

Criterion B-

ECLASS 4.1-

ETIM 4.0-

Power loss nominal load max.-

Conductor cross section solid min.-

Stripping length-

Low Voltage Directive-

Test field strength-

Voltage-

Conducted interference-

UNSPSC 6.01-

Insulation voltage input/output-

Connection method-

Conductor cross section flexible min.-

Standard - Electrical safety-

Frequency range-

Protection against overvoltage at the output (OVP)-

Maximum power dissipation in no-load condition-

Conductor cross section solid max.-

Conductor cross section AWG max.-

Mains variation/undervoltage-

UL approvals-

Electrostatic discharge-

ECLASS 11.0-

UNSPSC 13.2-

Height130 mm

Ambient temperature (start-up type tested)-40 °C

Degree of pollution2

Discharge current to PE< 3.5 mA

Mains buffering timetyp. 25 ms (400 V AC)

Protective circuit/componentVaristor

Connection in parallelYes, for redundancy and increased capacity

Output power960 W

MTBF (IEC 61709, SN 29500)> 890000 h (25 °C)

Insulation voltage output / PE500 V DC (routine test)

Conductor cross section solid min.0.2 mm²

Conductor cross section AWG max.10

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installationsEN 50178/VDE 0160 (PELV)

UL approvalsUL Listed UL 508

Contact discharge8 kV (Test Level 4)

Test field strength10 V/m (Test Level 3)

Input2 kV (Test Level 3 - symmetrical)

Criterion BTemporary impairment to operational behavior that is corrected by the device itself.

ECLASS 11.027040701

ECLASS 4.027040700

Depth179 mm

Degree of protectionIP20

Max. permissible relative humidity (operation)≤ 95 % (at 25 °C, non-condensing)

Input voltage range3x 320 V AC ... 575 V AC

AC frequency range45 Hz ... 65 Hz

REACh SVHCLead 7439-92-1

Recommended breaker for input protection6 A ... 16 A (AC: Characteristics B, C, D, K)

POWER BOOST (IBoost)22.5 A (-25 °C ... 40 °C permanent, UOUT = 48 V DC )

Connection in seriesyes

Active current limitationApprox. IBOOST = 22.5 A (for short-circuit)

Typical response time< 1 s

Housing materialSteel sheet, zinc-plated

Assembly instructionsalignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm verticallyalignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom

Connection methodScrew connection

Standard - Safety of transformersIEC 61558-2-17

Standard – Limitation of mains harmonic currentsEN 61000-3-2

Electromagnetic HF fieldEN 61000-4-3

Signal1 kV (Test Level 2 - asymmetrical)

Criterion ANormal operating behavior within the specified limits.

ECLASS 4.127040700

ETIM 4.0EC002540

UNSPSC 12.0139121004

Width with alternative assembly176 mm

Ambient temperature (operation)-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)

Installation height4000 m

Nominal power consumption1386 VA

Nominal output current (IN)20 A (-25 °C ... 60 °C, UOUT = 48 V DC)

Selective Fuse Breaking (ISFB)100 A (12 ms)

Protection against overvoltage at the output (OVP)< 60 V DC

Net weight2.5 kg

Insulation voltage input / PE3.5 kV AC (type test)

Mounting positionhorizontal DIN rail NS 35, EN 60715

Conductor cross section flexible min.0.2 mm²

Stripping length10 mm

EMC requirements for noise emissionEN 61000-6-3

Standard – Safety extra-low voltageIEC 60950-1 (SELV) and EN 60204-1 (PELV)

Standard - Approval for medical useIEC 60601-1, 2 x MOOP

CSACAN/CSA-C22.2 No. 60950-1-07

Electrostatic dischargeEN 61000-4-2

Low Voltage DirectiveConformance with Low Voltage Directive 2014/35/EC

Fast transients (burst)EN 61000-4-4

Output1 kV (Test Level 2 - symmetrical)

Voltage10 V (Test Level 3)

China RoHSEnvironmentally Friendly Use Period = 25;

ECLASS 5.027242200

ETIM 3.0EC001039

ETIM 6.0EC002540

UNSPSC 6.0130211502

UNSPSC 20.039121004

Width96 mm

Height with alternative assembly130 mm

Climatic class3K3 (in acc. with EN 60721)

Current consumption3x 2.1 A (400 V AC)

Type of protectionTransient surge protection

Setting range of the output voltage (USet)30 V DC ... 56 V DC (> 48 V DC, constant capacity restricted)

Feedback voltage resistancemax. 60 V DC

Residual ripple< 50 mVPP (with nominal values)

Power loss nominal load max.70 W

Insulation voltage input/output4 kV AC (type test)

Protection classI

Conductor cross section AWG min.18

EMC requirements for noise immunityEN 61000-6-1

Standard - Electrical safetyIEC 60950-1/VDE 0805 (SELV)

Standard - Equipment safetyBG (design tested)

Standard - Safe isolationDIN VDE 0100-410

Electromagnetic compatibilityConformance with EMC Directive 2014/30/EU

Frequency range0.15 MHz ... 80 MHz

Surge voltage load (surge)EN 61000-4-5

Conducted interferenceEN 61000-4-6

ECLASS 6.027049000

ETIM 7.0EC002540

UNSPSC 21.039121004

Depth with alternative assembly99 mm

Ambient temperature (storage/transport)-40 °C ... 85 °C

Nominal input voltage range3x 400 V AC ... 500 V AC

Frequency range DC0 Hz

Inrush current< 20 A (typical)

Nominal output voltage48 V DC ±1 %

Derating60 °C ... 70 °C (2.5%/K)

Control deviation< 1 % (change in load, static 10 % ... 90 %)

Maximum power dissipation in no-load condition24 W

Efficiency> 93 % (at 400 V AC and nominal values)

Conductor cross section solid max.6 mm²

Conductor cross section flexible max.4 mm²

Screw threadM3

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipmentEN 50178

Rail applicationsEN 50121-4

Discharge in air15 kV (Test Level 4)

CommentsCriterion A

I/O/Sasymmetrical

ECLASS 10.0.127040701

ECLASS 5.127242200

ECLASS 9.027040701

UNSPSC 1139121004

UNSPSC 18.039121004

ECLASS 7.027049002

UNSPSC 7.090139121004

UNSPSC 13.239121004

UNSPSC 19.039121004

Weight31.7 g

Maximum external conductor diameter8.5 mm

Ambient temperature (operation)-20 °C ... 70 °C

Width38.4 mm

Connection methodIDC fast connection

AWG solid max.23

No. of cable outlets1

Degree of pollution2

Conductor cross section0.14 mm² ... 0.36 mm² (solid)

Ambient temperature (storage/transport)-40 °C ... 70 °C

Contact surface materialGold over nickel

Rated current1.75 A

ECLASS 11.027440101

ECLASS 6.027260700

AWG solid min.26

Overvoltage categoryI

AWG multi-stranded max.23

Flammability rating according to UL 94V0

Ambient temperature (assembly)-5 °C ... 55 °C

Housing materialPA

Nominal voltage UN48 V

UNSPSC 1131261501

ECLASS 9.027440101

UNSPSC 13.239121409

UNSPSC 20.039121409

Height22.8 mm

Length77 mm

ECLASS 4.027260700

ETIM 2.0EC000764

ETIM 4.0EC001121

UNSPSC 12.0131261501

UNSPSC 21.039121409

Minimum external conductor diameter5 mm

AWG multi-stranded min.26

Cable outletstraight

UNSPSC 6.0131261501

Contact materialCopper alloy

Number of positions8

UNSPSC 19.039121409

GRP transmission propertiesCAT5 (IEC 11801:2002) CAT5 (IEC 11801:2002)

ECLASS 10.0.127440101

ECLASS 7.027440101

Contact carrier materialPC

Rated voltage (III/3)72 V (DC)

China RoHSEnvironmentally Friendly Use Period = 50 years

Connection in acc. with standardCUL

Transmission characteristics (category)CAT5 (IEC 11801:2002)

Contact resistance0.001 Ω (Wire – IDC)

ETIM 3.0EC001121

UNSPSC 7.090131261501

UNSPSC 18.039121409

ETIM 7.0EC002636

ECLASS 4.127260700

ECLASS 5.127260700

ETIM 6.0EC002636

ECLASS 5.027260700

Height-

Degree of protection-

Ambient temperature (operation)-

Max. permissible relative humidity (operation)-

Nominal power consumption-

Mains buffering time-

Protective circuit/component-

Feedback voltage resistance-

Output power-

Depth-

Inflammability class in acc. with UL 94 (housing / terminal blocks)-

Climatic class-

Input voltage range-

Inrush current-

Type of protection-

Width-

Installation distance top/bottom-

Ambient temperature (storage/transport)-

Nominal input voltage range-

Frequency range (fN)-

Input fuse-

Power factor (cos phi)-

Connection in parallel-

Residual ripple-

Control deviation-

Efficiency-

Standard – Safety extra-low voltage-

Discharge in air-

Comments-

Surge voltage load (surge)-

Voltage dips-

ECLASS 10.0.1-

ETIM 6.0-

UNSPSC 11-

UNSPSC 19.0-

Installation distance right/left-

Degree of pollution-

Current consumption-

Recommended breaker for input protection-

Nominal output current (IN)-

Nominal output voltage-

Connection in series-

Net weight-

Protection class-

Assembly instructions-

Conductor cross section AWG min.-

Screw thread-

Standard - Safety of transformers-

Standard – Limitation of mains harmonic currents-

Electromagnetic compatibility-

Contact discharge-

Input-

Criterion A-

ECLASS 4.0-

ECLASS 5.1-

ETIM 3.0-

UNSPSC 12.01-

UNSPSC 21.0-

MTBF (IEC 61709, SN 29500)-

Foot latch material-

Mounting position-

Conductor cross section flexible max.-

EMC requirements for noise immunity-

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

CSA-

Fast transients (burst)-

Electromagnetic HF field-

Output-

China RoHS-

ECLASS 6.0-

ECLASS 7.0-

UNSPSC 7.0901-

UNSPSC 18.0-

ECLASS 5.0-

ECLASS 9.0-

ETIM 7.0-

UNSPSC 20.0-

Derating-

Typical response time-

Housing material-

EMC requirements for noise emission-

Standard - Safe isolation-

Criterion B-

ECLASS 4.1-

ETIM 4.0-

Power loss nominal load max.-

Conductor cross section solid min.-

Stripping length-

Low Voltage Directive-

Test field strength-

Voltage-

Conducted interference-

UNSPSC 6.01-

Insulation voltage input/output-

Connection method-

Conductor cross section flexible min.-

Standard - Electrical safety-

Frequency range-

Protection against overvoltage at the output (OVP)-

Maximum power dissipation in no-load condition-

Conductor cross section solid max.-

Conductor cross section AWG max.-

Mains variation/undervoltage-

UL approvals-

Electrostatic discharge-

ECLASS 11.0-

UNSPSC 13.2-

Height-

Ambient temperature (start-up type tested)-

Degree of pollution-

Discharge current to PE-

Mains buffering time-

Protective circuit/component-

Connection in parallel-

Output power-

MTBF (IEC 61709, SN 29500)-

Insulation voltage output / PE-

Conductor cross section solid min.-

Conductor cross section AWG max.-

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

UL approvals-

Contact discharge-

Test field strength-

Input-

Criterion B-

ECLASS 11.0-

ECLASS 4.0-

Depth-

Degree of protection-

Max. permissible relative humidity (operation)-

Input voltage range-

AC frequency range-

REACh SVHC-

Recommended breaker for input protection-

POWER BOOST (IBoost)-

Connection in series-

Active current limitation-

Typical response time-

Housing material-

Assembly instructions-

Connection method-

Standard - Safety of transformers-

Standard – Limitation of mains harmonic currents-

Electromagnetic HF field-

Signal-

Criterion A-

ECLASS 4.1-

ETIM 4.0-

UNSPSC 12.01-

Width with alternative assembly-

Ambient temperature (operation)-

Installation height-

Nominal power consumption-

Nominal output current (IN)-

Selective Fuse Breaking (ISFB)-

Protection against overvoltage at the output (OVP)-

Net weight-

Insulation voltage input / PE-

Mounting position-

Conductor cross section flexible min.-

Stripping length-

EMC requirements for noise emission-

Standard – Safety extra-low voltage-

Standard - Approval for medical use-

CSA-

Electrostatic discharge-

Low Voltage Directive-

Fast transients (burst)-

Output-

Voltage-

China RoHS-

ECLASS 5.0-

ETIM 3.0-

ETIM 6.0-

UNSPSC 6.01-

UNSPSC 20.0-

Width-

Height with alternative assembly-

Climatic class-

Current consumption-

Type of protection-

Setting range of the output voltage (USet)-

Feedback voltage resistance-

Residual ripple-

Power loss nominal load max.-

Insulation voltage input/output-

Protection class-

Conductor cross section AWG min.-

EMC requirements for noise immunity-

Standard - Electrical safety-

Standard - Equipment safety-

Standard - Safe isolation-

Electromagnetic compatibility-

Frequency range-

Surge voltage load (surge)-

Conducted interference-

ECLASS 6.0-

ETIM 7.0-

UNSPSC 21.0-

Depth with alternative assembly-

Ambient temperature (storage/transport)-

Nominal input voltage range-

Frequency range DC-

Inrush current-

Nominal output voltage-

Derating-

Control deviation-

Maximum power dissipation in no-load condition-

Efficiency-

Conductor cross section solid max.-

Conductor cross section flexible max.-

Screw thread-

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment-

Rail applications-

Discharge in air-

Comments-

I/O/S-

ECLASS 10.0.1-

ECLASS 5.1-

ECLASS 9.0-

UNSPSC 11-

UNSPSC 18.0-

ECLASS 7.0-

UNSPSC 7.0901-

UNSPSC 13.2-

UNSPSC 19.0-

Weight-

Maximum external conductor diameter-

Ambient temperature (operation)-

Width-

Connection method-

AWG solid max.-

No. of cable outlets-

Degree of pollution-

Conductor cross section-

Ambient temperature (storage/transport)-

Contact surface material-

Rated current-

ECLASS 11.0-

ECLASS 6.0-

AWG solid min.-

Overvoltage category-

AWG multi-stranded max.-

Flammability rating according to UL 94-

Ambient temperature (assembly)-

Housing material-

Nominal voltage UN-

UNSPSC 11-

ECLASS 9.0-

UNSPSC 13.2-

UNSPSC 20.0-

Height-

Length-

ECLASS 4.0-

ETIM 2.0-

ETIM 4.0-

UNSPSC 12.01-

UNSPSC 21.0-

Minimum external conductor diameter-

AWG multi-stranded min.-

Cable outlet-

UNSPSC 6.01-

Contact material-

Number of positions-

UNSPSC 19.0-

GRP transmission properties-

ECLASS 10.0.1-

ECLASS 7.0-

Contact carrier material-

Rated voltage (III/3)-

China RoHS-

Connection in acc. with standard-

Transmission characteristics (category)-

Contact resistance-

ETIM 3.0-

UNSPSC 7.0901-

UNSPSC 18.0-

ETIM 7.0-

ECLASS 4.1-

ECLASS 5.1-

ETIM 6.0-

ECLASS 5.0-

Height90 mm

Degree of protectionIP20

Ambient temperature (operation)-25 °C ... 70 °C (> 55 °C Derating: 2.5 %/K)

Max. permissible relative humidity (operation)≤ 95 % (at 25 °C, non-condensing)

Nominal power consumption206.3 VA

Mains buffering time> 20 ms (120 V AC)

Protective circuit/componentVaristor

Feedback voltage resistance< 25 V DC

Output power100 W

Depth84 mm

Inflammability class in acc. with UL 94 (housing / terminal blocks)V0

Climatic class3K3 (in acc. with EN 60721)

Input voltage range85 V AC ... 264 V AC

Inrush current< 30 A (typical)

Type of protectionTransient surge protection

Width55 mm

Installation distance top/bottom30 mm / 30 mm

Ambient temperature (storage/transport)-40 °C ... 85 °C

Nominal input voltage range100 V AC ... 240 V AC

Frequency range (fN)50 Hz ... 60 Hz 10 %

Input fuse4 A (slow-blow, internal)

Power factor (cos phi)0.54

Connection in parallelYes, for redundancy and increased capacity

Residual ripple< 75 mVPP (with nominal values)

Control deviation< 1 % (change in load, static 10 % ... 90 %)

Efficiencytyp. 89 % (120 V AC)

Standard – Safety extra-low voltageIEC 62368-1 (SELV) und EN 60204-1 (PELV)

Discharge in air8 kV (Test Level 3)

CommentsCriterion A

Surge voltage load (surge)EN 61000-4-5

Voltage dipsEN 61000-4-11

ECLASS 10.0.127040701

ETIM 6.0EC002540

UNSPSC 1139121004

UNSPSC 19.039121004

Installation distance right/left0 mm / 0 mm

Degree of pollution2

Current consumption2.19 A (100 V AC)

Recommended breaker for input protection6 A ... 16 A (Characteristics B, C, D, K)

Nominal output current (IN)6.67 A (-25 °C ... 55 °C)

Nominal output voltage15 V DC ±1 %

Connection in seriesyes

Net weight0.34 kg

Protection classII (in closed control cabinet)

Assembly instructionsalignable: 0 mm horizontally, 30 mm vertically

Conductor cross section AWG min.24

Screw threadM3

Standard - Safety of transformersEN 61558-2-16

Standard – Limitation of mains harmonic currentsEN 61000-3-2

Electromagnetic compatibilityConformance with EMC Directive 2014/30/EU

Contact discharge6 kV (Test Level 3)

Input2 kV (Test Level 3 - symmetrical)

Criterion ANormal operating behavior within the specified limits.

ECLASS 4.027040700

ECLASS 5.127049000

ETIM 3.0EC001039

UNSPSC 12.0139121004

UNSPSC 21.039121004

MTBF (IEC 61709, SN 29500)> 727000 h (40 °C)

Foot latch materialPOM (Polyoxymethylen)

Mounting positionhorizontal DIN rail NS 35, EN 60715

Conductor cross section flexible max.2.5 mm²

EMC requirements for noise immunityEN 61000-6-1

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installationsEN 50178/VDE 0160 (PELV)

CSACAN/CSA-C22.2 No. 60950-1-07

Fast transients (burst)EN 61000-4-4

Electromagnetic HF fieldEN 61000-4-3

Output1 kV (Test Level 2 - symmetrical)

China RoHSEnvironmentally Friendly Use Period = 25;

ECLASS 6.027049000

ECLASS 7.027049002

UNSPSC 7.090139121004

UNSPSC 18.039121004

ECLASS 5.027049000

ECLASS 9.027040701

ETIM 7.0EC002540

UNSPSC 20.039121004

Derating55 °C ... 70 °C (2.5%/K)

Typical response time< 1 s

Housing materialPolycarbonate

EMC requirements for noise emissionEN 61000-6-3

Standard - Safe isolationDIN VDE 0100-410

Criterion BTemporary impairment to operational behavior that is corrected by the device itself.

ECLASS 4.127040700

ETIM 4.0EC000599

Power loss nominal load max.< 12 W

Conductor cross section solid min.0.2 mm²

Stripping length8 mm

Low Voltage DirectiveConformance with Low Voltage Directive 2014/35/EC

Test field strength10 V/m

Voltage10 V (Test Level 3)

Conducted interferenceEN 61000-4-6

UNSPSC 6.0130211502

Insulation voltage input/output4 kV AC (type test)

Connection methodScrew connection

Conductor cross section flexible min.0.2 mm²

Standard - Electrical safetyIEC 62368-1/VDE 0805 (SELV)

Frequency range10 kHz ... 80 MHz

Protection against overvoltage at the output (OVP)≤ 25 V DC

Maximum power dissipation in no-load condition< 0.4 W

Conductor cross section solid max.2.5 mm²

Conductor cross section AWG max.14

Mains variation/undervoltageEN 61000-4-11

UL approvalsUL/C-UL listed UL 508

Electrostatic dischargeEN 61000-4-2

ECLASS 11.027040701

UNSPSC 13.239121004

Height-

Ambient temperature (start-up type tested)-

Degree of pollution-

Discharge current to PE-

Mains buffering time-

Protective circuit/component-

Connection in parallel-

Output power-

MTBF (IEC 61709, SN 29500)-

Insulation voltage output / PE-

Conductor cross section solid min.-

Conductor cross section AWG max.-

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

UL approvals-

Contact discharge-

Test field strength-

Input-

Criterion B-

ECLASS 11.0-

ECLASS 4.0-

Depth-

Degree of protection-

Max. permissible relative humidity (operation)-

Input voltage range-

AC frequency range-

REACh SVHC-

Recommended breaker for input protection-

POWER BOOST (IBoost)-

Connection in series-

Active current limitation-

Typical response time-

Housing material-

Assembly instructions-

Connection method-

Standard - Safety of transformers-

Standard – Limitation of mains harmonic currents-

Electromagnetic HF field-

Signal-

Criterion A-

ECLASS 4.1-

ETIM 4.0-

UNSPSC 12.01-

Width with alternative assembly-

Ambient temperature (operation)-

Installation height-

Nominal power consumption-

Nominal output current (IN)-

Selective Fuse Breaking (ISFB)-

Protection against overvoltage at the output (OVP)-

Net weight-

Insulation voltage input / PE-

Mounting position-

Conductor cross section flexible min.-

Stripping length-

EMC requirements for noise emission-

Standard – Safety extra-low voltage-

Standard - Approval for medical use-

CSA-

Electrostatic discharge-

Low Voltage Directive-

Fast transients (burst)-

Output-

Voltage-

China RoHS-

ECLASS 5.0-

ETIM 3.0-

ETIM 6.0-

UNSPSC 6.01-

UNSPSC 20.0-

Width-

Height with alternative assembly-

Climatic class-

Current consumption-

Type of protection-

Setting range of the output voltage (USet)-

Feedback voltage resistance-

Residual ripple-

Power loss nominal load max.-

Insulation voltage input/output-

Protection class-

Conductor cross section AWG min.-

EMC requirements for noise immunity-

Standard - Electrical safety-

Standard - Equipment safety-

Standard - Safe isolation-

Electromagnetic compatibility-

Frequency range-

Surge voltage load (surge)-

Conducted interference-

ECLASS 6.0-

ETIM 7.0-

UNSPSC 21.0-

Depth with alternative assembly-

Ambient temperature (storage/transport)-

Nominal input voltage range-

Frequency range DC-

Inrush current-

Nominal output voltage-

Derating-

Control deviation-

Maximum power dissipation in no-load condition-

Efficiency-

Conductor cross section solid max.-

Conductor cross section flexible max.-

Screw thread-

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment-

Rail applications-

Discharge in air-

Comments-

I/O/S-

ECLASS 10.0.1-

ECLASS 5.1-

ECLASS 9.0-

UNSPSC 11-

UNSPSC 18.0-

ECLASS 7.0-

UNSPSC 7.0901-

UNSPSC 13.2-

UNSPSC 19.0-

Weight-

Maximum external conductor diameter-

Ambient temperature (operation)-

Width-

Connection method-

AWG solid max.-

No. of cable outlets-

Degree of pollution-

Conductor cross section-

Ambient temperature (storage/transport)-

Contact surface material-

Rated current-

ECLASS 11.0-

ECLASS 6.0-

AWG solid min.-

Overvoltage category-

AWG multi-stranded max.-

Flammability rating according to UL 94-

Ambient temperature (assembly)-

Housing material-

Nominal voltage UN-

UNSPSC 11-

ECLASS 9.0-

UNSPSC 13.2-

UNSPSC 20.0-

Height-

Length-

ECLASS 4.0-

ETIM 2.0-

ETIM 4.0-

UNSPSC 12.01-

UNSPSC 21.0-

Minimum external conductor diameter-

AWG multi-stranded min.-

Cable outlet-

UNSPSC 6.01-

Contact material-

Number of positions-

UNSPSC 19.0-

GRP transmission properties-

ECLASS 10.0.1-

ECLASS 7.0-

Contact carrier material-

Rated voltage (III/3)-

China RoHS-

Connection in acc. with standard-

Transmission characteristics (category)-

Contact resistance-

ETIM 3.0-

UNSPSC 7.0901-

UNSPSC 18.0-

ETIM 7.0-

ECLASS 4.1-

ECLASS 5.1-

ETIM 6.0-

ECLASS 5.0-

Height-

Degree of protection-

Ambient temperature (operation)-

Max. permissible relative humidity (operation)-

Nominal power consumption-

Mains buffering time-

Protective circuit/component-

Feedback voltage resistance-

Output power-

Depth-

Inflammability class in acc. with UL 94 (housing / terminal blocks)-

Climatic class-

Input voltage range-

Inrush current-

Type of protection-

Width-

Installation distance top/bottom-

Ambient temperature (storage/transport)-

Nominal input voltage range-

Frequency range (fN)-

Input fuse-

Power factor (cos phi)-

Connection in parallel-

Residual ripple-

Control deviation-

Efficiency-

Standard – Safety extra-low voltage-

Discharge in air-

Comments-

Surge voltage load (surge)-

Voltage dips-

ECLASS 10.0.1-

ETIM 6.0-

UNSPSC 11-

UNSPSC 19.0-

Installation distance right/left-

Degree of pollution-

Current consumption-

Recommended breaker for input protection-

Nominal output current (IN)-

Nominal output voltage-

Connection in series-

Net weight-

Protection class-

Assembly instructions-

Conductor cross section AWG min.-

Screw thread-

Standard - Safety of transformers-

Standard – Limitation of mains harmonic currents-

Electromagnetic compatibility-

Contact discharge-

Input-

Criterion A-

ECLASS 4.0-

ECLASS 5.1-

ETIM 3.0-

UNSPSC 12.01-

UNSPSC 21.0-

MTBF (IEC 61709, SN 29500)-

Foot latch material-

Mounting position-

Conductor cross section flexible max.-

EMC requirements for noise immunity-

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

CSA-

Fast transients (burst)-

Electromagnetic HF field-

Output-

China RoHS-

ECLASS 6.0-

ECLASS 7.0-

UNSPSC 7.0901-

UNSPSC 18.0-

ECLASS 5.0-

ECLASS 9.0-

ETIM 7.0-

UNSPSC 20.0-

Derating-

Typical response time-

Housing material-

EMC requirements for noise emission-

Standard - Safe isolation-

Criterion B-

ECLASS 4.1-

ETIM 4.0-

Power loss nominal load max.-

Conductor cross section solid min.-

Stripping length-

Low Voltage Directive-

Test field strength-

Voltage-

Conducted interference-

UNSPSC 6.01-

Insulation voltage input/output-

Connection method-

Conductor cross section flexible min.-

Standard - Electrical safety-

Frequency range-

Protection against overvoltage at the output (OVP)-

Maximum power dissipation in no-load condition-

Conductor cross section solid max.-

Conductor cross section AWG max.-

Mains variation/undervoltage-

UL approvals-

Electrostatic discharge-

ECLASS 11.0-

UNSPSC 13.2-

Height130 mm

Ambient temperature (start-up type tested)-40 °C

Degree of pollution2

Discharge current to PE< 3.5 mA

Mains buffering timetyp. 25 ms (400 V AC)

Protective circuit/componentVaristor

Connection in parallelYes, for redundancy and increased capacity

Output power960 W

MTBF (IEC 61709, SN 29500)> 890000 h (25 °C)

Insulation voltage output / PE500 V DC (routine test)

Conductor cross section solid min.0.2 mm²

Conductor cross section AWG max.10

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installationsEN 50178/VDE 0160 (PELV)

UL approvalsUL Listed UL 508

Contact discharge8 kV (Test Level 4)

Test field strength10 V/m (Test Level 3)

Input2 kV (Test Level 3 - symmetrical)

Criterion BTemporary impairment to operational behavior that is corrected by the device itself.

ECLASS 11.027040701

ECLASS 4.027040700

Depth179 mm

Degree of protectionIP20

Max. permissible relative humidity (operation)≤ 95 % (at 25 °C, non-condensing)

Input voltage range3x 320 V AC ... 575 V AC

AC frequency range45 Hz ... 65 Hz

REACh SVHCLead 7439-92-1

Recommended breaker for input protection6 A ... 16 A (AC: Characteristics B, C, D, K)

POWER BOOST (IBoost)22.5 A (-25 °C ... 40 °C permanent, UOUT = 48 V DC )

Connection in seriesyes

Active current limitationApprox. IBOOST = 22.5 A (for short-circuit)

Typical response time< 1 s

Housing materialSteel sheet, zinc-plated

Assembly instructionsalignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm verticallyalignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom

Connection methodScrew connection

Standard - Safety of transformersIEC 61558-2-17

Standard – Limitation of mains harmonic currentsEN 61000-3-2

Electromagnetic HF fieldEN 61000-4-3

Signal1 kV (Test Level 2 - asymmetrical)

Criterion ANormal operating behavior within the specified limits.

ECLASS 4.127040700

ETIM 4.0EC002540

UNSPSC 12.0139121004

Width with alternative assembly176 mm

Ambient temperature (operation)-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)

Installation height4000 m

Nominal power consumption1386 VA

Nominal output current (IN)20 A (-25 °C ... 60 °C, UOUT = 48 V DC)

Selective Fuse Breaking (ISFB)100 A (12 ms)

Protection against overvoltage at the output (OVP)< 60 V DC

Net weight2.5 kg

Insulation voltage input / PE3.5 kV AC (type test)

Mounting positionhorizontal DIN rail NS 35, EN 60715

Conductor cross section flexible min.0.2 mm²

Stripping length10 mm

EMC requirements for noise emissionEN 61000-6-3

Standard – Safety extra-low voltageIEC 60950-1 (SELV) and EN 60204-1 (PELV)

Standard - Approval for medical useIEC 60601-1, 2 x MOOP

CSACAN/CSA-C22.2 No. 60950-1-07

Electrostatic dischargeEN 61000-4-2

Low Voltage DirectiveConformance with Low Voltage Directive 2014/35/EC

Fast transients (burst)EN 61000-4-4

Output1 kV (Test Level 2 - symmetrical)

Voltage10 V (Test Level 3)

China RoHSEnvironmentally Friendly Use Period = 25;

ECLASS 5.027242200

ETIM 3.0EC001039

ETIM 6.0EC002540

UNSPSC 6.0130211502

UNSPSC 20.039121004

Width96 mm

Height with alternative assembly130 mm

Climatic class3K3 (in acc. with EN 60721)

Current consumption3x 2.1 A (400 V AC)

Type of protectionTransient surge protection

Setting range of the output voltage (USet)30 V DC ... 56 V DC (> 48 V DC, constant capacity restricted)

Feedback voltage resistancemax. 60 V DC

Residual ripple< 50 mVPP (with nominal values)

Power loss nominal load max.70 W

Insulation voltage input/output4 kV AC (type test)

Protection classI

Conductor cross section AWG min.18

EMC requirements for noise immunityEN 61000-6-1

Standard - Electrical safetyIEC 60950-1/VDE 0805 (SELV)

Standard - Equipment safetyBG (design tested)

Standard - Safe isolationDIN VDE 0100-410

Electromagnetic compatibilityConformance with EMC Directive 2014/30/EU

Frequency range0.15 MHz ... 80 MHz

Surge voltage load (surge)EN 61000-4-5

Conducted interferenceEN 61000-4-6

ECLASS 6.027049000

ETIM 7.0EC002540

UNSPSC 21.039121004

Depth with alternative assembly99 mm

Ambient temperature (storage/transport)-40 °C ... 85 °C

Nominal input voltage range3x 400 V AC ... 500 V AC

Frequency range DC0 Hz

Inrush current< 20 A (typical)

Nominal output voltage48 V DC ±1 %

Derating60 °C ... 70 °C (2.5%/K)

Control deviation< 1 % (change in load, static 10 % ... 90 %)

Maximum power dissipation in no-load condition24 W

Efficiency> 93 % (at 400 V AC and nominal values)

Conductor cross section solid max.6 mm²

Conductor cross section flexible max.4 mm²

Screw threadM3

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipmentEN 50178

Rail applicationsEN 50121-4

Discharge in air15 kV (Test Level 4)

CommentsCriterion A

I/O/Sasymmetrical

ECLASS 10.0.127040701

ECLASS 5.127242200

ECLASS 9.027040701

UNSPSC 1139121004

UNSPSC 18.039121004

ECLASS 7.027049002

UNSPSC 7.090139121004

UNSPSC 13.239121004

UNSPSC 19.039121004

Weight31.7 g

Maximum external conductor diameter8.5 mm

Ambient temperature (operation)-20 °C ... 70 °C

Width38.4 mm

Connection methodIDC fast connection

AWG solid max.23

No. of cable outlets1

Degree of pollution2

Conductor cross section0.14 mm² ... 0.36 mm² (solid)

Ambient temperature (storage/transport)-40 °C ... 70 °C

Contact surface materialGold over nickel

Rated current1.75 A

ECLASS 11.027440101

ECLASS 6.027260700

AWG solid min.26

Overvoltage categoryI

AWG multi-stranded max.23

Flammability rating according to UL 94V0

Ambient temperature (assembly)-5 °C ... 55 °C

Housing materialPA

Nominal voltage UN48 V

UNSPSC 1131261501

ECLASS 9.027440101

UNSPSC 13.239121409

UNSPSC 20.039121409

Height22.8 mm

Length77 mm

ECLASS 4.027260700

ETIM 2.0EC000764

ETIM 4.0EC001121

UNSPSC 12.0131261501

UNSPSC 21.039121409

Minimum external conductor diameter5 mm

AWG multi-stranded min.26

Cable outletstraight

UNSPSC 6.0131261501

Contact materialCopper alloy

Number of positions8

UNSPSC 19.039121409

GRP transmission propertiesCAT5 (IEC 11801:2002) CAT5 (IEC 11801:2002)

ECLASS 10.0.127440101

ECLASS 7.027440101

Contact carrier materialPC

Rated voltage (III/3)72 V (DC)

China RoHSEnvironmentally Friendly Use Period = 50 years

Connection in acc. with standardCUL

Transmission characteristics (category)CAT5 (IEC 11801:2002)

Contact resistance0.001 Ω (Wire – IDC)

ETIM 3.0EC001121

UNSPSC 7.090131261501

UNSPSC 18.039121409

ETIM 7.0EC002636

ECLASS 4.127260700

ECLASS 5.127260700

ETIM 6.0EC002636

ECLASS 5.027260700

Height-

Degree of protection-

Ambient temperature (operation)-

Max. permissible relative humidity (operation)-

Nominal power consumption-

Mains buffering time-

Protective circuit/component-

Feedback voltage resistance-

Output power-

Depth-

Inflammability class in acc. with UL 94 (housing / terminal blocks)-

Climatic class-

Input voltage range-

Inrush current-

Type of protection-

Width-

Installation distance top/bottom-

Ambient temperature (storage/transport)-

Nominal input voltage range-

Frequency range (fN)-

Input fuse-

Power factor (cos phi)-

Connection in parallel-

Residual ripple-

Control deviation-

Efficiency-

Standard – Safety extra-low voltage-

Discharge in air-

Comments-

Surge voltage load (surge)-

Voltage dips-

ECLASS 10.0.1-

ETIM 6.0-

UNSPSC 11-

UNSPSC 19.0-

Installation distance right/left-

Degree of pollution-

Current consumption-

Recommended breaker for input protection-

Nominal output current (IN)-

Nominal output voltage-

Connection in series-

Net weight-

Protection class-

Assembly instructions-

Conductor cross section AWG min.-

Screw thread-

Standard - Safety of transformers-

Standard – Limitation of mains harmonic currents-

Electromagnetic compatibility-

Contact discharge-

Input-

Criterion A-

ECLASS 4.0-

ECLASS 5.1-

ETIM 3.0-

UNSPSC 12.01-

UNSPSC 21.0-

MTBF (IEC 61709, SN 29500)-

Foot latch material-

Mounting position-

Conductor cross section flexible max.-

EMC requirements for noise immunity-

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

CSA-

Fast transients (burst)-

Electromagnetic HF field-

Output-

China RoHS-

ECLASS 6.0-

ECLASS 7.0-

UNSPSC 7.0901-

UNSPSC 18.0-

ECLASS 5.0-

ECLASS 9.0-

ETIM 7.0-

UNSPSC 20.0-

Derating-

Typical response time-

Housing material-

EMC requirements for noise emission-

Standard - Safe isolation-

Criterion B-

ECLASS 4.1-

ETIM 4.0-

Power loss nominal load max.-

Conductor cross section solid min.-

Stripping length-

Low Voltage Directive-

Test field strength-

Voltage-

Conducted interference-

UNSPSC 6.01-

Insulation voltage input/output-

Connection method-

Conductor cross section flexible min.-

Standard - Electrical safety-

Frequency range-

Protection against overvoltage at the output (OVP)-

Maximum power dissipation in no-load condition-

Conductor cross section solid max.-

Conductor cross section AWG max.-

Mains variation/undervoltage-

UL approvals-

Electrostatic discharge-

ECLASS 11.0-

UNSPSC 13.2-

Height-

Ambient temperature (start-up type tested)-

Degree of pollution-

Discharge current to PE-

Mains buffering time-

Protective circuit/component-

Connection in parallel-

Output power-

MTBF (IEC 61709, SN 29500)-

Insulation voltage output / PE-

Conductor cross section solid min.-

Conductor cross section AWG max.-

Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations-

UL approvals-

Contact discharge-

Test field strength-

Input-

Criterion B-

ECLASS 11.0-

ECLASS 4.0-

Depth-

Degree of protection-

Max. permissible relative humidity (operation)-

Input voltage range-

AC frequency range-

REACh SVHC-

Recommended breaker for input protection-

POWER BOOST (IBoost)-

Connection in series-

Active current limitation-

Typical response time-

Housing material-

Assembly instructions-

Connection method-

Standard - Safety of transformers-

Standard – Limitation of mains harmonic currents-

Electromagnetic HF field-

Signal-

Criterion A-

ECLASS 4.1-

ETIM 4.0-

UNSPSC 12.01-

Width with alternative assembly-

Ambient temperature (operation)-

Installation height-

Nominal power consumption-

Nominal output current (IN)-

Selective Fuse Breaking (ISFB)-

Protection against overvoltage at the output (OVP)-

Net weight-

Insulation voltage input / PE-

Mounting position-

Conductor cross section flexible min.-

Stripping length-

EMC requirements for noise emission-

Standard – Safety extra-low voltage-

Standard - Approval for medical use-

CSA-

Electrostatic discharge-

Low Voltage Directive-

Fast transients (burst)-

Output-

Voltage-

China RoHS-

ECLASS 5.0-

ETIM 3.0-

ETIM 6.0-

UNSPSC 6.01-

UNSPSC 20.0-

Width-

Height with alternative assembly-

Climatic class-

Current consumption-

Type of protection-

Setting range of the output voltage (USet)-

Feedback voltage resistance-

Residual ripple-

Power loss nominal load max.-

Insulation voltage input/output-

Protection class-

Conductor cross section AWG min.-

EMC requirements for noise immunity-

Standard - Electrical safety-

Standard - Equipment safety-

Standard - Safe isolation-

Electromagnetic compatibility-

Frequency range-

Surge voltage load (surge)-

Conducted interference-

ECLASS 6.0-

ETIM 7.0-

UNSPSC 21.0-

Depth with alternative assembly-

Ambient temperature (storage/transport)-

Nominal input voltage range-

Frequency range DC-

Inrush current-

Nominal output voltage-

Derating-

Control deviation-

Maximum power dissipation in no-load condition-

Efficiency-

Conductor cross section solid max.-

Conductor cross section flexible max.-

Screw thread-

Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment-

Rail applications-

Discharge in air-

Comments-

I/O/S-

ECLASS 10.0.1-

ECLASS 5.1-

ECLASS 9.0-

UNSPSC 11-

UNSPSC 18.0-

ECLASS 7.0-

UNSPSC 7.0901-

UNSPSC 13.2-

UNSPSC 19.0-