3274228 Phoenix Contact Terminal Blocks

Product Details

• Maximum load current
  57 A (with 10 mm² conductor cross section)
• Open side panel
  No
• Result of power-frequency withstand voltage test
  Test passed
• Result of flexion and pull-out test
  Test passed
• Bending test turns
  135
• Tensile test result
  Test passed
• Result of temperature-rise test
  Test passed
• Result of thermal test
  Test passed
• Ageing test for screwless modular terminal block temperature cycles
  192
• Acceleration
  30g
• Test directions
  X-, Y- and Z-axis (pos. and neg.)
• Specific optical density of smoke NFPA 130 (ASTM E 662)
  passed
• Fire protection for rail vehicles (DIN EN 45545-2) R23
  HL 1 - HL 3
• Connection in acc. with standard
  IEC 60947-7-1
• Conductor cross section flexible min.
  0.5 mm²
• Max. AWG conductor cross section, flexible
  10
• Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
  1.5 mm²
• Ambient temperature (assembly)
  -5 °C ... 70 °C
• ECLASS 4.1
  27141121
• ETIM 6.0
  EC000897
ETIM 3.0
EC000897
Rated surge voltage
8 kV
Nominal voltage UN
690 V
Result of surge voltage test
Test passed
Result of tight fit on support
Test passed
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Result of aging test
Test passed
Test duration per axis
5 h
Shock form
Half-sine
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Length
28.6 mm
Conductor cross section solid max.
10 mm²
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
Connection
Feed-in stage
Permissible humidity (storage/transport)
30 % ... 70 %
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 9.0
27141120
UNSPSC 11
39121410
Degree of pollution
3
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Bending test rotation speed
10 rpm
Tight fit on carrier
NS 35
Short-time current
1.2 kA
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
130 °C
Surface flammability NFPA 130 (ASTM E 162)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Stripping length
10 mm ... 12 mm
Conductor cross section AWG max.
8
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 11.0
27141120
ECLASS 5.0
27141120
ETIM 7.0
EC000897
UNSPSC 12.01
39121410
UNSPSC 20.0
39121410
Nominal cross section
2.5 mm²
Insulating material
PA
Insulating material group
I
Nominal current IN
41 A (with 6 mm² conductor cross section)
Finger protection
guaranteed
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Result of voltage-drop test
Test passed
Short circuit stability result
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
Test spectrum
Service life test category 2, bogie-mounted
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Shock duration
18 ms
Static insulating material application in cold
-60 °C
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Width
56.5 mm
Height NS 15
31.4 mm
Conductor cross section flexible, with ferrule without plastic sleeve max.
6 mm²
Conductor cross section flexible, with ferrule with plastic sleeve max.
6 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
ECLASS 10.0.1
27141120
ECLASS 4.0
27141121
ECLASS 5.1
27141120
ETIM 4.0
EC000897
UNSPSC 6.01
30211811
Note
The max. load current must not be exceeded by the total current of all connected conductors.
Nominal cross section feed-in
6 mm²
Overvoltage category
III
Maximum total current
57 A (with 10 mm² conductor cross section)
Back of the hand protection
guaranteed
Power frequency withstand voltage setpoint
1.89 kV
Bending test conductor cross section/weight
0.5 mm² / 0.3 kg
Setpoint
5 N
Conductor cross section short circuit testing
10 mm²
Oscillation, broadband noise test result
Test passed
ASD level
6.12 (m/s2)2/Hz
Shock test result
Test passed
Number of shocks per direction
3
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Connection method
Push-in connection
Conductor cross section solid min.
1 mm²
Conductor cross section flexible max.
10 mm²
Min. AWG conductor cross section, flexible
20
Internal cylindrical gage
A3
Value
1 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
ECLASS 6.0
27141100
ECLASS 7.0
27141120
UNSPSC 7.0901
39121410
UNSPSC 13.2
39121410
UNSPSC 19.0
39121410
UNSPSC 18.0
39121410
UNSPSC 21.0
39121410
Number of levels
1
Color
orange
Number of connections
19
Conductor cross section AWG min.
20
Potentials
1
Maximum power dissipation for nominal condition
1.31 W (the value is based on one connection block and is multiplied according to the pin assignment)
Flammability rating according to UL 94
V0
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Connection cross sections directly pluggable
1 mm² 10 mm²