3274208 Phoenix Contact Terminal Blocks

Product Details

• Nominal current IN
  41 A (with 6 mm² conductor cross section)
• Back of the hand protection
  guaranteed
• Result of flexion and pull-out test
  Test passed
• Tight fit on carrier
  NS 35
• Result of temperature-rise test
  Test passed
• Conductor cross section short circuit testing
  10 mm²
• Result of aging test
  Test passed
• Test specification, oscillation, broadband noise
  DIN EN 50155 (VDE 0115-200):2008-03
• Number of shocks per direction
  3
• Fire protection for rail vehicles (DIN EN 45545-2) R22
  HL 1 - HL 3
• Length
  28.6 mm
• Overvoltage category
  III
• Maximum total current
  57 A (with 10 mm² conductor cross section)
• Power frequency withstand voltage setpoint
  1.89 kV
• Result of power-frequency withstand voltage test
  Test passed
• Setpoint
  5 N
• Result of thermal test
  Test passed
• ASD level
  6.12 (m/s2)2/Hz
• Shock form
  Half-sine
• Relative insulation material temperature index (Elec., UL 746 B)
  130 °C
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Value
1 mm²
Flammability rating according to UL 94
V0
Nominal voltage UN
690 V
Bending test rotation speed
10 rpm
Result of tight fit on support
Test passed
Short circuit stability result
Test passed
Ageing test for screwless modular terminal block temperature cycles
192
Test duration per axis
5 h
Shock duration
18 ms
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Nominal cross section feed-in
6 mm²
Insulating material
PA
Open side panel
No
Result of surge voltage test
Test passed
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Tensile test result
Test passed
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Test spectrum
Service life test category 2, bogie-mounted
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Width
41 mm
ECLASS 11.0
27141120
Color
black/yellow
Maximum load current
57 A (with 10 mm² conductor cross section)
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Bending test conductor cross section/weight
0.5 mm² / 0.3 kg
Bending test turns
135
Result of voltage-drop test
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Test directions
X-, Y- and Z-axis (pos. and neg.)
Shock test result
Test passed
Surface flammability NFPA 130 (ASTM E 162)
passed
Connection method
Push-in connection
Note
The max. load current must not be exceeded by the total current of all connected conductors.
Rated surge voltage
8 kV
Nominal cross section
2.5 mm²
Maximum power dissipation for nominal condition
1.31 W (the value is based on one connection block and is multiplied according to the pin assignment)
Finger protection
guaranteed
Acceleration
30g
Static insulating material application in cold
-60 °C
Height NS 15
31.4 mm
Connection in acc. with standard
IEC 60947-7-1
Conductor cross section flexible max.
10 mm²
Min. AWG conductor cross section, flexible
20
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.5 mm²
Internal cylindrical gage
A3
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 10.0.1
27141120
ECLASS 6.0
27141100
ETIM 3.0
EC000897
UNSPSC 12.01
39121410
UNSPSC 21.0
39121410
Number of levels
1
Degree of pollution
3
Short-time current
1.2 kA
Oscillation, broadband noise test result
Test passed
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
130 °C
Conductor cross section solid max.
10 mm²
Conductor cross section AWG min.
20
Conductor cross section flexible min.
0.5 mm²
Conductor cross section flexible, with ferrule with plastic sleeve max.
6 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Ambient temperature (assembly)
-5 °C ... 70 °C
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 4.1
27141121
ETIM 4.0
EC000897
UNSPSC 6.01
30211811
UNSPSC 13.2
39121410
UNSPSC 18.0
39121410
Number of connections
13
Insulating material group
I
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Stripping length
10 mm ... 12 mm
Conductor cross section solid min.
1 mm²
Max. AWG conductor cross section, flexible
10
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
Connection cross sections directly pluggable
1 mm² 10 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1.5 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
ECLASS 4.0
27141121
ECLASS 5.1
27141120
ECLASS 7.0
27141120
ETIM 6.0
EC000897
UNSPSC 11
39121410
UNSPSC 19.0
39121410
Potentials
1
Conductor cross section AWG max.
8
Conductor cross section flexible, with ferrule without plastic sleeve max.
6 mm²
Connection
Feed-in stage
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 5.0
27141120
ECLASS 9.0
27141120
ETIM 7.0
EC000897
UNSPSC 7.0901
39121410
UNSPSC 20.0
39121410