3274202 Phoenix Contact Terminal Blocks

Product Details

• Ambient temperature (storage/transport)
  -25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
• ECLASS 10.0.1
  27141120
• ECLASS 5.1
  27141120
• ETIM 4.0
  EC000897
• UNSPSC 7.0901
  39121410
• UNSPSC 18.0
  39121410
• Value
  1 mm²
• Ambient temperature (assembly)
  -5 °C ... 70 °C
• Ambient temperature (actuation)
  -5 °C ... 70 °C
• ECLASS 7.0
  27141120
• ETIM 6.0
  EC000897
• UNSPSC 6.01
  30211811
• UNSPSC 20.0
  39121410
• Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
  1.5 mm²
• ECLASS 11.0
  27141120
• ECLASS 5.0
  27141120
• ECLASS 6.0
  27141100
• UNSPSC 11
  39121410
• UNSPSC 21.0
  39121410
• Permissible humidity (storage/transport)
  30 % ... 70 %
ECLASS 4.1
27141121
ECLASS 9.0
27141120
ETIM 7.0
EC000897
UNSPSC 13.2
39121410
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 4.0
27141121
ETIM 3.0
EC000897
UNSPSC 12.01
39121410
UNSPSC 19.0
39121410
Note
The max. load current must not be exceeded by the total current of all connected conductors.
Nominal cross section feed-in
6 mm²
Degree of pollution
3
Open side panel
No
Power frequency withstand voltage setpoint
1.89 kV
Bending test turns
135
Result of temperature-rise test
Test passed
Result of thermal test
Test passed
Ageing test for screwless modular terminal block temperature cycles
192
Test spectrum
Service life test category 2, bogie-mounted
Test directions
X-, Y- and Z-axis (pos. and neg.)
Number of shocks per direction
3
Static insulating material application in cold
-60 °C
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Stripping length
10 mm ... 12 mm
Connection in acc. with standard
IEC 60947-7-1
Nominal cross section
2.5 mm²
Flammability rating according to UL 94
V0
Maximum load current
57 A (with 10 mm² conductor cross section)
Nominal current IN
41 A (with 6 mm² conductor cross section)
Result of surge voltage test
Test passed
Result of flexion and pull-out test
Test passed
Bending test conductor cross section/weight
0.5 mm² / 0.3 kg
Short circuit stability result
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Number of levels
1
Overvoltage category
III
Rated surge voltage
8 kV
Maximum power dissipation for nominal condition
1.31 W (the value is based on one connection block and is multiplied according to the pin assignment)
Finger protection
guaranteed
Tensile test result
Test passed
Tight fit on carrier
NS 35
Result of voltage-drop test
Test passed
Short-time current
1.2 kA
ASD level
6.12 (m/s2)2/Hz
Acceleration
30g
Shock duration
18 ms
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Width
41 mm
Length
28.6 mm
Conductor cross section solid min.
1 mm²
Conductor cross section AWG max.
8
Conductor cross section flexible, with ferrule without plastic sleeve max.
6 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Potentials
1
Insulating material
PA
Maximum total current
57 A (with 10 mm² conductor cross section)
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Back of the hand protection
guaranteed
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Setpoint
5 N
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Oscillation, broadband noise test result
Test passed
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Shock form
Half-sine
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
130 °C
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Conductor cross section solid max.
10 mm²
Conductor cross section flexible min.
0.5 mm²
Conductor cross section flexible, with ferrule with plastic sleeve max.
6 mm²
Number of connections
13
Color
black
Insulating material group
I
Nominal voltage UN
690 V
Result of power-frequency withstand voltage test
Test passed
Bending test rotation speed
10 rpm
Result of tight fit on support
Test passed
Conductor cross section short circuit testing
10 mm²
Result of aging test
Test passed
Test duration per axis
5 h
Shock test result
Test passed
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Surface flammability NFPA 130 (ASTM E 162)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Height NS 15
31.4 mm
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.5 mm²
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Connection method
Push-in connection
Conductor cross section AWG min.
20
Max. AWG conductor cross section, flexible
10
Connection cross sections directly pluggable
1 mm² 10 mm²
Connection
Feed-in stage
Conductor cross section flexible max.
10 mm²
Min. AWG conductor cross section, flexible
20
Internal cylindrical gage
A3