3069840 Phoenix Contact Terminal Blocks

Product Details

• Number of positions
  17
• Color
  gray
• Rated surge voltage
  4 kV
• Insulating material group
  I
• Finger protection
  guaranteed
• Power frequency withstand voltage setpoint
  1.89 kV
• Bending test conductor cross section/weight
  0.5 mm² / 0.3 kg
• Note
  The measuring transducer block is replaced every 100 cycles.
• Short-time current
  0.15 kA
• Ageing test for screwless modular terminal block temperature cycles
  192
• Test directions
  X-, Y- and Z-axis (pos. and neg.)
• Shock duration
  18 ms
• Calorimetric heat release NFPA 130 (ASTM E 1354)
  27,5 MJ/kg
• Number of levels
  1
• Test surge voltage
  5 kV
• Terminal block mounting
  0.8 Nm ... 1 Nm
• Result of the test for mechanical stability of terminal points (5 x conductor connection)
  Test passed
• Result of flexion and pull-out test
  Test passed
• Bending test rotation speed
  10 rpm
• Setpoint
  5 N
Conductor cross section short circuit testing
4 mm²
Oscillation, broadband noise test result
Test passed
ASD level
6.12 (m/s2)2/Hz
Test duration per axis
5 h
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Height
56.5 mm
Connection method
Push-in connection
Number of connections
34
Insulating material
PA
Maximum power dissipation for nominal condition
1.31 W
Nominal voltage UN
400 V AC/DC
Note regarding shock protection
When test disconnect plug is plugged in.
Result of power-frequency withstand voltage test
Test passed
Result of tight fit on support
Test passed
Result of voltage-drop test
Test passed
Short circuit stability result
Test passed
Result of aging test
Test passed
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Acceleration
30g
Number of shocks per direction
3
Surface flammability NFPA 130 (ASTM E 162)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Pitch
8.2 mm
Conductor cross section solid max.
10 mm²
Conductor cross section AWG min.
20
Max. AWG conductor cross section, flexible
10
Conductor cross section flexible, with ferrule with plastic sleeve max.
6 mm²
ECLASS 9.0
27141126
Potentials
17
Flammability rating according to UL 94
V0
Maximum load current
30 A (with 6 mm² conductor cross section)
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Back of the hand protection
guaranteed
Bending test turns
135
Result of temperature-rise test
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
Test spectrum
Service life test category 2, bogie-mounted
Shock form
Half-sine
Static insulating material application in cold
-60 °C
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Nominal cross section
6 mm²
Overvoltage category
III
Open side panel
No
Result of surge voltage test
Test passed
Tensile test result
Test passed
Width
172.2 mm
Length
81 mm
Connection
1 level
Conductor cross section AWG max.
8
Conductor cross section flexible, with ferrule without plastic sleeve min.
1 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1.5 mm²
Internal cylindrical gage
A5
Min. tightening torque of the mounting screw:
0.8 Nm
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 10.0.1
27141126
ECLASS 6.0
27141100
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Stripping length
12 mm
Connection in acc. with standard
IEC 60947-7-1
Conductor cross section flexible max.
6 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
6 mm²
Conductor cross section flexible, with ferrule with plastic sleeve min.
1 mm²
Max. tightening torque of the mounting screw:
1 Nm
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
ECLASS 11.0
27141126
ETIM 4.0
EC000897
UNSPSC 21.0
39121410
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Result of thermal test
Test passed
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
ETIM 6.0
EC000902
UNSPSC 19.0
39121410
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
Shock test result
Test passed
ETIM 7.0
EC000902
Min. AWG conductor cross section, flexible
20
Mounting type
Wall mounting
Ambient temperature (assembly)
-5 °C ... 70 °C
UNSPSC 18.0
39121410
Connection cross sections directly pluggable
1 mm² 10 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
REACh SVHC
Lead 7439-92-1
Plate thickness
1 mm ... 4 mm
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 7.0
27141126
UNSPSC 20.0
39121410
Conductor cross section solid min.
1 mm²
ECLASS 5.0
27141100
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
UNSPSC 13.2
39121410
Conductor cross section flexible min.
0.5 mm²
ECLASS 5.1
27141100