2967620 Phoenix Contact Control Relays

Product Details

• Utilization restriction
  EMC: class A product, see manufacturer's declaration in the download area
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Typical response time
  8 ms
• Power dissipation for nominal condition
  0.43 W
• Minimum switching voltage
  12 V DC (at 10 mA)
• Limiting continuous current
  10 A
• Mechanical service life
  3x 107 cycles
• Mounting position
  any
• Stripping length
  8 mm
• Conductor cross section AWG
  26 ... 14
• Insulation
  Safe isolation, reinforced insulation
• REACh SVHC
  Lead 7439-92-1
• China RoHS
  Environmentally Friendly Use Period = 50 years
• ECLASS 9.0
  27371601
• ETIM 3.0
  EC001437
• ETIM 7.0
  EC001437
• UNSPSC 19.0
  39122334
• UNSPSC 20.0
  39122334
• Width
  14 mm
• Depth
  94 mm
Degree of protection
RT II (Relay)
Typical release time
10 ms
Operating voltage display
Yellow LED
Type of switch contact
Single contact
Maximum inrush current
30 A (300 ms)
Switching capacity
2 A (at 24 V, DC13)
Assembly instructions
In rows with zero spacing
Conductor cross section flexible
0.14 mm² ... 2.5 mm²
Designation
Corrosive gas test
Pollution degree
2
Identification
ISA-S71.04. G3 Harsh Group
ECLASS 4.1
27371100
ECLASS 6.0
27371600
ETIM 2.0
EC001437
UNSPSC 7.0901
39121515
UNSPSC 12.01
39121515
UNSPSC 21.0
39122334
Height
80 mm
Typical input current at UN
18 mA
Protective circuit
Reverse polarity protection Polarity protection diode
Contact material
AgNi
Min. switching current
10 mA (at 12 V)
Interrupting rating (ohmic load) max.
240 W (at 24 V DC)
Operating mode
100% operating factor
Flammability rating according to UL 94
V0 (Housing)
Screw thread
M3
Conductor cross section solid
0.14 mm² ... 2.5 mm²
Rated surge voltage
6 kV
Overvoltage category
III
ECLASS 4.0
27371100
ECLASS 5.0
27371600
ECLASS 7.0
27371601
UNSPSC 6.01
30211916
UNSPSC 13.2
39122334
UNSPSC 18.0
39122334
Ambient temperature (operation)
-40 °C ... 60 °C
Nominal input voltage UN
24 V DC
Contact type
1 changeover contact
Maximum switching voltage
250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...)
Interrupting rating (ohmic load) max. bridged
144 W (for 24 V DC. Value applies to connections 12. If connections 12 are bridged, the normal value applies.)
Test voltage
4 kV AC (50 Hz, 1 min., winding/contact)
Connection name
Contact side
Connection method
Screw connection
Connection in acc. with standard
CUL
Standards/regulations
IEC 60664
ECLASS 10.0.1
27371601
ECLASS 11.0
27371601
ECLASS 5.1
27371600
ETIM 4.0
EC001437
ETIM 6.0
EC001437
UNSPSC 11
39121515