2909521 Phoenix Contact Control Relays

Product Details

• Height
  80 mm
• Typical response time
  7 ms
• Operating voltage display
  Yellow LED
• Ambient temperature (operation)
  -20 °C ... 60 °C (UL)
• Typical release time
  10 ms
• Contact type
  1 changeover contact
• Maximum inrush current
  30 A (300 ms)
• Switching capacity
  2 A (at 24 V, DC13)
• Test voltage
  4 kV AC (50 Hz, 1 min., winding/contact)
• Connection name
  Contact side
• Conductor cross section flexible
  0.14 mm² ... 2.5 mm²
• Standards/regulations
  IEC 60664
• Rated surge voltage
  6 kV
• REACh SVHC
  Lead 7439-92-1
• ECLASS 5.0
  27371600
• ETIM 2.0
  EC001437
• UNSPSC 6.01
  30211916
• UNSPSC 12.01
  39121515
• UNSPSC 19.0
  39122334
• Width
  14 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Nominal input voltage UN
230 V AC
Protective circuit
Bridge rectifier Bridge rectifier
Type of switch contact
Single contact
Min. switching current
10 mA (at 12 V)
Flammability rating according to UL 94
V0 (Housing)
Assembly instructions
In rows with zero spacing
Screw thread
M3
Conductor cross section AWG
26 ... 14
Pollution degree
2
Certificate
IECEx IBE 16.0029X
ECLASS 11.0
27371601
ECLASS 7.0
27371601
ECLASS 9.0
27371601
UNSPSC 13.2
39122334
UNSPSC 20.0
39122334
Depth
94 mm
Degree of protection
RT III (Relay)
Power dissipation for nominal condition
1.04 W
Minimum switching voltage
12 V (at 10 mA)
Interrupting rating (ohmic load) max.
240 W (at 24 V DC)
Operating mode
100% operating factor
Mechanical service life
3x 107 cycles
Stripping length
8 mm
Connection method
Screw connection
Rated insulation voltage
250 V AC
Insulation
Safe isolation, reinforced insulation
Identification
ISA-S71.04. G3 Harsh Group
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 5.1
27371600
ETIM 6.0
EC001437
UNSPSC 11
39121515
UNSPSC 7.0901
39121515
Utilization restriction
EMC: class A product, see manufacturer's declaration in the download area
Typical input current at UN
4.5 mA
Contact material
AgNi
Maximum switching voltage
250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...)
Limiting continuous current
10 A
Interrupting rating (ohmic load) max. bridged
144 W (for 24 V DC. Value applies to connections 12. If connections 12 are bridged, the normal value applies.)
Mounting position
any
Conductor cross section solid
0.14 mm² ... 2.5 mm²
Designation
Corrosive gas test
Overvoltage category
III
ECLASS 10.0.1
27371601
ECLASS 6.0
27371600
ETIM 3.0
EC001437
ETIM 4.0
EC001437
ETIM 7.0
EC001437
UNSPSC 18.0
39122334
UNSPSC 21.0
39122334