2905012 Phoenix Contact DC/DC Converters

Product Details

• Width
  48 mm
• Height with alternative assembly
  130 mm
• Installation distance right/left
  0 mm / 0 mm (≤ 70 °C)
• Ambient temperature (start-up type tested)
  -40 °C
• Degree of protection
  IP20
• Degree of pollution
  2
• Input voltage range
  67.2 V DC ... 154 V DC
• Input fuse
  10 A 150 V DC (internal (device protection))
• Protective circuit/component
  Varistor
• POWER BOOST (IBoost)
  12.5 A (-40°C ... 40°C permanent, UOUT = 24 V DC )
• Protection against overvoltage at the output (OVP)
  < 35 V DC
• Max. capacitive load
  unlimited
• Residual ripple
  < 20 mVPP
• Protection class
  I
• Conductor cross section flexible min.
  0.2 mm²
• Screw thread
  M3
• Contact discharge
  8 kV (Test Level 4)
• Net weight
  0.9 kg
• Connection method
  Screw connection
• Conductor cross section solid max.
  2.5 mm²
Conductor cross section AWG max.
12
Standard - Electrical safety
EN 60950-1/VDE 0805 (SELV)
UL approvals
UL/C-UL listed UL 508
Electrostatic discharge
EN 61000-4-2
Output
1 kV (Test Level 3 - symmetrical)
Conducted interference
EN 61000-4-6
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 5.1
27210900
ECLASS 9.0
27210901
UNSPSC 20.0
39121041
Depth
125 mm
Depth with alternative assembly
51 mm
Installation distance top/bottom (active)
50 mm / 50 mm (≤ 70 °C)
Installation distance top/bottom
50 mm / 50 mm (≤ 70 °C)
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Climatic class
3K3 (in acc. with EN 60721)
Current consumption
3.5 A (96 V DC)
Mains buffering time
typ. 10 ms (96 V DC)
Nominal output voltage
24 V DC ±1 %
Nominal output current (IN)
10 A (-40 °C ... 60 °C)
Derating
60 °C ... 70 °C (2.5%/K)
Feedback voltage resistance
35 V DC
Power loss nominal load max.
22 W (UIN 110 V DC)
Insulation voltage input/output
1.5 kV (type test)
Conductor cross section flexible max.
2.5 mm²
EMC requirements for noise emission
EN 61000-6-3
Rail applications
EN 50121-4
Frequency range
0.15 MHz ... 80 MHz
Input
2 kV (Test Level 4 - symmetrical)
Voltage
10 V (Test Level 3)
REACh SVHC
Lead 7439-92-1
ECLASS 4.1
27210900
ETIM 6.0
EC002046
UNSPSC 21.0
39121041
Height
130 mm
Width with alternative assembly
122 mm
Installation distance right/left (active)
15 mm / 15 mm (≤ 70 °C)
Ambient temperature (operation)
-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Max. permissible relative humidity (operation)
100 % (at 25 °C, non-condensing)
Nominal input voltage range
96 V DC ... 110 V DC
Inrush current
< 10 A (typical)
Type of protection
Transient surge protection
Setting range of the output voltage (USet)
18 V DC ... 29.5 V DC (> 24 V DC, constant capacity restricted)
Selective Fuse Breaking (ISFB)
60 A (12 ms)
Connection in series
yes
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Peak switching voltages nominal load
< 10 mVPP (20 MHz)
MTBF (IEC 61709, SN 29500)
> 1357000 h (25 °C)
Assembly instructions
alignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm verticallyalignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
Conductor cross section AWG min.
24
Standard – Safety extra-low voltage
EN 60950-1 (SELV)
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Test field strength
10 V/m (Test Level 3)
Surge voltage load (surge)
EN 61000-4-5
I/O/S
asymmetrical
ECLASS 11.0
27210901
ECLASS 7.0
27210901
UNSPSC 18.0
39121041
Signal
1 kV (Test Level 2 - asymmetrical)
ECLASS 10.0.1
27210901
ECLASS 5.0
27210900
UNSPSC 13.2
39121041
ETIM 7.0
EC002046
Standard - Safe isolation
DIN VDE 0100-410
Comments
Criterion A
Criterion A
Normal operating behavior within the specified limits.
ECLASS 6.0
27210900
UNSPSC 19.0
39121041
Maximum power dissipation in no-load condition
4 W (UIN 110 V DC)
Conductor cross section solid min.
0.2 mm²
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Fast transients (burst)
EN 61000-4-4
ECLASS 4.0
27210900
Mounting position
horizontal DIN rail NS 35, EN 60715
EMC requirements for noise immunity
EN 61000-6-1
Discharge in air
15 kV (Test Level 4)
Active current limitation
18 A
Efficiency
> 92 % (UIN 96 V DC / UOUT 24 V DC)
Connection in parallel
Yes, for redundancy and increased capacity
Stripping length
7 mm
Electromagnetic HF field
EN 61000-4-3