2905007 Phoenix Contact DC/DC Converters

Product Details

• Height
  130 mm
• Height with alternative assembly
  130 mm
• Installation distance top/bottom
  50 mm / 50 mm (≤ 70 °C)
• Depth with alternative assembly
  35 mm
• Degree of protection
  IP20
• Max. permissible relative humidity (operation)
  ≤ 95 % (at 25 °C, non-condensing)
• Current consumption
  12 A (12 V, IBOOST)
• Width
  32 mm
• Installation distance right/left
  0 mm / 0 mm (≤ 70 °C)
• Ambient temperature (start-up type tested)
  -40 °C
• Input voltage range
  9 V DC ... 18 V DC
• Protective circuit/component
  Varistor
• Selective Fuse Breaking (ISFB)
  48 A (12 ms)
• Max. capacitive load
  unlimited
• Active current limitation
  15 A
• MTBF (IEC 61709, SN 29500)
  > 1614000 h (25 °C)
• Width with alternative assembly
  122 mm
• Installation distance top/bottom (active)
  50 mm / 50 mm (≤ 70 °C)
• Climatic class
  3K3 (in acc. with EN 60721)
• Mains buffering time
  typ. 3 ms (12 V DC)
Nominal output current (IN)
8 A (-25 °C ... 60 °C)
Feedback voltage resistance
25 V DC
Peak switching voltages nominal load
< 10 mVPP (20 MHz)
Insulation voltage input/output
1.5 kV (type test)
Assembly instructions
alignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm verticallyalignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
Conductor cross section AWG min.
24
Standard - Safe isolation
DIN VDE 0100-410
Electrostatic discharge
EN 61000-4-2
Electromagnetic HF field
EN 61000-4-3
Output
1 kV (Test Level 3 - symmetrical)
Criterion A
Normal operating behavior within the specified limits.
ECLASS 4.0
27210900
ECLASS 5.1
27210900
ETIM 6.0
EC002046
Depth
125 mm
Installation distance right/left (active)
15 mm / 15 mm (≤ 70 °C)
Ambient temperature (operation)
-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Nominal input voltage range
12 V DC
Type of protection
Transient surge protection
Nominal output voltage
12 V DC ±1 %
POWER BOOST (IBoost)
10 A (-25 °C ... 40 °C permanent, UOUT = 12 V DC )
Connection in series
yes
Power loss nominal load max.
11.8 W
Connection method
Screw connection
Conductor cross section solid max.
2.5 mm²
Stripping length
7 mm
EMC requirements for noise emission
EN 61000-6-3
Contact discharge
8 kV (Test Level 4)
Discharge in air
15 kV (Test Level 4)
Surge voltage load (surge)
EN 61000-4-5
Voltage
10 V (Test Level 3)
ECLASS 5.0
27210900
UNSPSC 13.2
39121041
UNSPSC 19.0
39121041
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Degree of pollution
2
Input fuse
25 A (internal (device protection))
Setting range of the output voltage (USet)
5 V DC ... 18 V DC (> 12 V DC, constant capacity restricted)
Connection in parallel
Yes, for redundancy and increased capacity
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Net weight
0.8 kg
Protection class
III
Conductor cross section solid min.
0.2 mm²
Conductor cross section AWG max.
12
EMC requirements for noise immunity
EN 61000-6-1
Standard – Safety extra-low voltage
EN 60950-1 (SELV)
Comments
Criterion A
Signal
1 kV (Test Level 2 - asymmetrical)
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 11.0
27210901
ECLASS 9.0
27210901
UNSPSC 21.0
39121041
Inrush current
< 6 A (typical)
Derating
60 °C ... 70 °C (2.5%/K)
Protection against overvoltage at the output (OVP)
< 25 V DC
Residual ripple
< 20 mVPP
Maximum power dissipation in no-load condition
1.5 W
Efficiency
> 89 %
Conductor cross section flexible max.
2.5 mm²
Standard - Electrical safety
EN 60950-1/VDE 0805 (SELV)
Rail applications
EN 50121-4
UL approvals
UL/C-UL listed UL 508
Frequency range
0.1 MHz ... 80 MHz
Fast transients (burst)
EN 61000-4-4
I/O/S
asymmetrical
ECLASS 10.0.1
27210901
ECLASS 4.1
27210900
ETIM 7.0
EC002046
UNSPSC 20.0
39121041
Mounting position
horizontal DIN rail NS 35, EN 60715
Conductor cross section flexible min.
0.2 mm²
Screw thread
M3
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Test field strength
10 V/m (Test Level 3)
Input
1 kV (Test Level 1 - symmetrical)
Conducted interference
EN 61000-4-6
REACh SVHC
Lead 7439-92-1
ECLASS 6.0
27210900
ECLASS 7.0
27210901
UNSPSC 18.0
39121041