2903364 Phoenix Contact Control Relays

Product Details

• Degree of protection
  IP20 (Relay base)
• Typical release time
  8 ms
• Operating voltage display
  Yellow LED
• Minimum switching voltage
  5 V (at 100 mA)
• Test voltage
  4 kVrms (50 Hz, 1 min., winding/contact)
• Connection name
  Contact side
• Conductor cross-section solid (2 conductors with same cross section)
  0.5 mm² ... 1.5 mm²
• Standards/regulations
  DIN EN 50178
• Overvoltage category
  III
• Designation
  Corrosive gas test
• ECLASS 4.0
  27371100
• ECLASS 5.0
  27371600
• ETIM 3.0
  EC001437
• UNSPSC 13.2
  39122334
• UNSPSC 19.0
  39122334
• Depth
  68 mm
• Typical input current at UN
  9 mA
• Power dissipation for nominal condition
  0.22 W
• Maximum switching voltage
  250 V AC/DC
• Operating mode
  100% operating factor
Mounting position
any
Conductor cross section solid
0.5 mm² ... 4 mm²
Conductor cross section flexible
0.5 mm² ... 2.5 mm²
Rated insulation voltage
250 V AC
REACh SVHC
Lead 7439-92-1
ECLASS 11.0
27371601
ECLASS 7.0
27371601
UNSPSC 7.0901
39121516
UNSPSC 12.01
39121516
Height
84 mm
Coil voltage
24 V DC
Contact type
1 N/O contact
Min. switching current
10 mA (at 12 V)
Switching capacity
2 A (at 24 V, DC13)
Mechanical service life
approx. 2x 107 cycles
Connection method
Screw connection
Conductor cross section flexible (2 conductors with same cross section)
0.5 mm² ... 1.5 mm²
Rated surge voltage
6 kV
Insulation
safe isolation
China RoHS
Environmentally Friendly Use Period = 50 years
ETIM 2.0
EC001437
ETIM 4.0
EC001437
UNSPSC 11
39121516
UNSPSC 20.0
39122334
Width
6.2 mm
Nominal input voltage UN
24 V DC
Typical response time
5 ms
Contact material
AgSnO
Limiting continuous current
6 A
Note
the following values are applicable if a gold layer is destroyed
Assembly instructions
In rows with zero spacing
Conductor cross section AWG
20 ... 12 (solid)
Pollution degree
2
ECLASS 4.1
27371100
ECLASS 6.0
27371600
ETIM 6.0
EC001437
UNSPSC 18.0
39122334
Utilization restriction
EMC: class A product, see manufacturer's declaration in the download area
Input voltage range in reference to UN
see diagram
Protective circuit
Damping diode
Type of switch contact
Single contact
Maximum inrush current
50 mA
Interrupting rating (ohmic load) max.
140 W (at 24 V DC)
Flammability rating according to UL 94
V2 (Housing)
Service life, electrical
see diagram
Stripping length
7 mm
Torque
0.5 Nm ... 0.6 Nm
Identification
ISA-S71.04. G3 Harsh Group
ECLASS 10.0.1
27371601
ECLASS 5.1
27371600
ECLASS 9.0
27371601
ETIM 7.0
EC001437
UNSPSC 6.01
30211917
UNSPSC 21.0
39122334