2902042 Phoenix Contact Electrical Measuring & Monitoring Instruments

Product Details

• Utilization restriction
  EMC: class A product, see manufacturer's declaration in the download area
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Height
  109.81 mm
• Number of inputs
  1
• Number of outputs
  1
• Max. output voltage
  11 V
• Transmission Behavior
  1:1 to input signal
• Stripping length
  10 mm
• Maximum temperature coefficient
  0.01 %/K
• Maximum transmission error
  0.1 % (of final value)
• Electrical isolation
  Reinforced insulation in accordance with IEC 61010-1
• Housing material
  PBT
• Depth
  119.2 mm
• Permissible humidity (operation)
  5 % ... 95 % (non-condensing)
• Short-circuit current
  < 15 mA
• Nominal supply voltage
  24 V DC
• Typical current consumption
  25 mA (24 V DC)
• Conductor cross section AWG
  24 ... 12 (flexible)
• Temperature coefficient, typical
  0.01 %/K
• Protective circuit
  Transient protection
Identification
UL 508 Listed
Ambient temperature (operation)
-40 °C ... 70 °C
Noise immunity
EN 61000-6-2 When being exposed to interference, there may be minimal deviations.
Load/output load voltage output
≥ 10 kΩ
Supply voltage range
9.6 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715))
Power consumption
≤ 200 mW (at 9.6 V DC)
Screw thread
M3
Step response (10-90%)
approx. 10 ms
Degree of pollution
2
Noise emission
EN 61000-6-4
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 2
Certificate
DNV GL TAA00002UA
Humidity
B
EMC
A
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 6.0
27210100
UNSPSC 7.0901
39121004
UNSPSC 21.0
39121008
Width
6.2 mm
Maximum altitude
≤ 2000 m
Configurable/programmable
no
Voltage output signal
0 V ... 10 V
Connection method
Screw connection
Conductor cross section solid
0.2 mm² ... 1.5 mm² (with ferrule)
Torque
0.5 Nm ... 0.6 Nm
Limit frequency (3 dB)
approx. 30 Hz
Test voltage, input/output/supply
3 kV (50 Hz, 1 min.)
Color
gray
Designation
Shipbuilding approval
Vibration
A
Enclosure
Required protection according to the Rules shall be provided upon installation on board
ECLASS 4.0
27210100
ECLASS 7.0
27210120
ETIM 6.0
EC002653
UNSPSC 18.0
39121008
Degree of protection
IP20 (not assessed by UL)
Input resistance of voltage input
approx. 1 MΩ
Voltage input signal
0 V ... 10 V
Ripple
< 20 mVPP (at 10 kΩ)
Conductor cross section flexible
0.14 mm² ... 2.5 mm²
No. of channels
1
Overvoltage category
II
Electromagnetic compatibility
Conformance with EMC directive
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 2
Assembly instructions
The T connector can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715.
Standards/regulations
EN 61000-4-6
REACh SVHC
Lead 7439-92-1
ECLASS 4.1
27210100
ETIM 7.0
EC002653
UNSPSC 11
39121004
UNSPSC 19.0
39121008
UNSPSC 20.0
39121008
Rated insulation voltage
300 V (effective)
Mounting position
any
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 2
Temperature
B
ECLASS 11.0
27210120
ECLASS 5.1
27210100
ETIM 4.0
EC002653
UNSPSC 12.01
39121004
ECLASS 10.0.1
27210120
ECLASS 5.0
27210100
ECLASS 9.0
27210120
UNSPSC 6.01
30211502
UNSPSC 13.2
39121008