2902039 Phoenix Contact Electrical Measuring & Monitoring Instruments

Product Details

• Height
  109.81 mm
• Degree of protection
  IP20 (not assessed by UL)
• Noise immunity
  EN 61000-6-2 When being exposed to interference, there may be minimal deviations.
• Current input signal
  0 mA ... 20 mA (via DIP switch)
• Max. output current
  22 mA
• Load/output load voltage output
  ≥ 10 kΩ
• Designation
  Shipbuilding approval
• EMC
  A
• ECLASS 11.0
  27210120
• ECLASS 7.0
  27210120
• UNSPSC 19.0
  39121008
• Enclosure
  Required protection according to the Rules shall be provided upon installation on board
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Configurable/programmable
  Yes
• Input resistance of voltage input
  > 1000 kΩ
• Number of outputs
  1
• Conductor cross section flexible
  0.14 mm² ... 2.5 mm²
• Mounting position
  any
• Identification
  UL 508 Listed
• ECLASS 4.1
  27210100
ETIM 6.0
EC002653
Depth
119.2 mm
Number of inputs
1
Voltage output signal
0 V ... 5 V (via DIP switch)
Ripple
< 20 mVPP (at 600 Ω)
Typical current consumption
25 mA (Current output, at 24 V DC incl. load)
Stripping length
10 mm
Temperature
B
Humidity
B
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 5.1
27210100
ECLASS 9.0
27210120
UNSPSC 13.2
39121008
UNSPSC 21.0
39121008
Utilization restriction
EMC: class A product, see manufacturer's declaration in the download area
Permissible humidity (operation)
5 % ... 95 % (non-condensing)
max. input voltage
33 V
Input resistance current input
approx. 63 Ω (+0.7 V for test diode)
Load/output load current output
≤ 600 Ω (at 20 mA)
Standards/regulations
EN 61000-4-6
REACh SVHC
Lead 7439-92-1
ECLASS 4.0
27210100
ECLASS 6.0
27210100
ETIM 7.0
EC002653
UNSPSC 20.0
39121008
Voltage input signal
0 V ... 5 V (via DIP switch)
Max. input current
24 mA
Current output signal
0 mA ... 20 mA (via DIP switch)
Nominal supply voltage
24 V DC
Maximum temperature coefficient
0.01 %/K
Vibration
A
UNSPSC 18.0
39121008
ECLASS 5.0
27210100
ETIM 4.0
EC002653
ECLASS 10.0.1
27210120
Ambient temperature (operation)
-40 °C ... 70 °C
Temperature coefficient, typical
0.01 %/K
Certificate
DNV GL TAA00002UA
Connection method
Push-in connection
Conductor cross section solid
0.2 mm² ... 2.5 mm² (with ferrule)
No. of channels
1
Step response (10-90%)
< 8.5 ms (with 30 Hz filter)
Supply voltage range
9.6 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715))
Limit frequency (3 dB)
30 Hz (via DIP switch)
Protective circuit
Transient protection
Maximum transmission error
≤ 0.1 % (of final value)
Width
6.2 mm
Short-circuit current
< 32 mA
Electrical isolation
Reinforced insulation in accordance with IEC 61010-1
Power consumption
≤ 800 mW (at IOUT = 20 mA, 9.6 V DC, 600 Ω load)
Conductor cross section AWG
24 ... 12 (flexible)
Test voltage, input/output/supply
3 kV (50 Hz, 1 min.)
Noise emission
EN 61000-6-4
Rated insulation voltage
300 V (effective)
Housing material
PBT
Electromagnetic compatibility
Conformance with EMC directive
Color
gray
Degree of pollution
2
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 2
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 2
Assembly instructions
The T connector can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715.
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 2
Overvoltage category
II