2901998 Phoenix Contact Electrical Measuring & Monitoring Instruments

Product Details

• Ambient temperature (operation)
  -40 °C ... 70 °C
• Permissible humidity (operation)
  5 % ... 95 % (non-condensing)
• Noise immunity
  EN 61000-6-2 When being exposed to interference, there may be minimal deviations.
• Transmission Behavior
  1:1 to input signal
• Screw thread
  M3
• Utilization restriction
  EMC: class A product, see manufacturer's declaration in the download area
• Number of inputs
  1
• Maximum transmission error
  0.1 % (of final value)
• Configurable/programmable
  no
• Electrical isolation
  Reinforced insulation in accordance with IEC 61010-1
• Rated insulation voltage
  300 V (effective)
• EMC
  A
• Max. output current
  22 mA
• Power consumption
  ≤ 800 mW (at 9.6 V DC)
• Number of outputs
  1
• Fire protection for rail vehicles (DIN EN 45545-2) R23
  HL 1 - HL 2
• Width
  6.2 mm
• Current output signal
  0 mA ... 20 mA
• Nominal supply voltage
  24 V DC
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
Conductor cross section AWG
24 ... 12 (flexible)
Limit frequency (3 dB)
approx. 30 Hz
Degree of pollution
2
Temperature
B
Enclosure
Required protection according to the Rules shall be provided upon installation on board
ECLASS 4.1
27210100
Housing material
PBT
ECLASS 7.0
27210120
Height
109.81 mm
Degree of protection
IP20 (not assessed by UL)
Overvoltage category
II
Input resistance current input
approx. 63 Ω (+0.7 V for test diode)
Load/output load current output
≤ 600 Ω (at 20 mA)
Typical current consumption
25 mA (24 V DC)
Connection method
Screw connection
Torque
0.5 Nm ... 0.6 Nm
Temperature coefficient, typical
0.01 %/K
Electromagnetic compatibility
Conformance with EMC directive
Conductor cross section solid
0.2 mm² ... 1.5 mm² (with ferrule)
Protective circuit
Transient protection
Depth
119.2 mm
Maximum altitude
≤ 2000 m
Current input signal
0 mA ... 20 mA
Ripple
< 20 mVPP (at 600 Ω)
Supply voltage range
9.6 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715))
Test voltage, input/output/supply
3 kV (50 Hz, 1 min.)
Noise emission
EN 61000-6-4
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 2
Standards/regulations
EN 61000-4-6
Humidity
B
ECLASS 11.0
27210120
ECLASS 9.0
27210120
Stripping length
10 mm
Conductor cross section flexible
0.14 mm² ... 2.5 mm²
No. of channels
1
Step response (10-90%)
approx. 10 ms
ETIM 6.0
EC002653
UNSPSC 18.0
39121008
Color
gray
Vibration
A
ECLASS 10.0.1
27210120
UNSPSC 21.0
39121008
UNSPSC 13.2
39121008
UNSPSC 7.0901
39121004
Maximum temperature coefficient
0.01 %/K
Designation
Shipbuilding approval
REACh SVHC
Lead 7439-92-1
ECLASS 5.1
27210100
ETIM 7.0
EC002653
UNSPSC 20.0
39121008
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 2
Certificate
DNV GL TAA00002UA
ECLASS 6.0
27210100
ECLASS 5.0
27210100
UNSPSC 12.01
39121004
Mounting position
any
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 4.0
27210100
UNSPSC 6.01
30211502
UNSPSC 11
39121004
UNSPSC 19.0
39121008
Identification
UL 508 Listed
ETIM 4.0
EC002653
Assembly instructions
The T connector can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715.