2900297 Phoenix Contact Control Relays

Product Details

• Width
  14 mm
• Depth
  94 mm
• Degree of protection
  RT II (Relay)
• Typical response time
  7 ms
• Operating voltage display
  Yellow LED
• Min. switching current
  10 mA (at 12 V)
• Interrupting rating (ohmic load) max.
  240 W (at 24 V DC)
• Mechanical service life
  3x 107 cycles
• Conductor cross section solid
  0.14 mm² ... 2.5 mm²
• Conductor cross section AWG
  26 ... 14
• Insulation
  Safe isolation, reinforced insulation
• China RoHS
  Environmentally Friendly Use Period = 50 years
• ECLASS 4.1
  27371000
• ETIM 2.0
  EC001437
• ETIM 6.0
  EC001437
• UNSPSC 7.0901
  39121515
• UNSPSC 13.2
  39122334
• Utilization restriction
  EMC: class A product, see manufacturer's declaration in the download area
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Typical release time
  10 ms
Type of switch contact
Single contact
Maximum inrush current
30 A (300 ms)
Switching capacity
2 A (at 24 V, DC13)
Assembly instructions
In rows with zero spacing
Stripping length
8 mm
Conductor cross section flexible
0.14 mm² ... 2.5 mm²
Connection in acc. with standard
CUL
Pollution degree
2
REACh SVHC
Lead 7439-92-1
Height
80 mm
Nominal input voltage UN
230 V AC
Protective circuit
Bridge rectifier Bridge rectifier
Contact material
AgNi
Minimum switching voltage
12 V (at 10 mA)
Interrupting rating (ohmic load) max. bridged
144 W (for 24 V DC. Value applies to connections 12. If connections 12 are bridged, the normal value applies.)
Flammability rating according to UL 94
V0 (Housing)
Mounting position
any
Designation
Corrosive gas test
Rated surge voltage
6 kV
Identification
ISA-S71.04. G3 Harsh Group
ECLASS 10.0.1
27371601
ECLASS 6.0
27371600
ETIM 4.0
EC001437
UNSPSC 6.01
30211916
UNSPSC 12.01
39121515
UNSPSC 20.0
39122334
Ambient temperature (operation)
-40 °C ... 55 °C
Typical input current at UN
4.3 mA (at 220 V DC)
Power dissipation for nominal condition
0.99 W
Contact type
1 changeover contact
Maximum switching voltage
250 V AC/DC (The separating plate PLC-ATP should be installed for voltages larger than 250 V (L1, L2, L3) between identical terminal blocks in adjacent modules. Potential bridging is then carried out with FBST 8-PLC... or ...FBST 500...)
Limiting continuous current
10 A
Operating mode
100% operating factor
Connection name
Contact side
Connection method
Push-in connection
Standards/regulations
IEC 60664
Overvoltage category
III
ECLASS 11.0
27371601
ECLASS 5.0
27371600
ECLASS 7.0
27371601
ETIM 3.0
EC001437
UNSPSC 11
39121515
UNSPSC 19.0
39122334
ECLASS 4.0
27371000
ECLASS 5.1
27371600
ECLASS 9.0
27371601
ETIM 7.0
EC001437
UNSPSC 18.0
39122334
UNSPSC 21.0
39122334