2700578 Phoenix Contact Electrical Safety Devices

Product Details

• Utilization restriction
  EMC: class A product, see manufacturer's declaration in the download area
• Rated control circuit supply voltage US
  24 V DC -15 % / +10 % (A1/A2)
• Input current range "0" signal
  0 mA ... 2 mA (for safe Off)
• Output name
  Confirmation current path
• Contact material
  AgCuNi, + Au
• Sq. Total current
  36 A2 (13/14, see to derating)
• Ambient temperature (operation)
  -40 °C ... 70 °C (observe derating)
• Max. permissible humidity (storage/transport)
  75 % (on average, 85% infrequently, non-condensing)
• Power consumption at US
  typ. 1.2 W
• Depth
  114.5 mm
• Max. permissible relative humidity (operation)
  75 % (on average, 85% infrequently, non-condensing)
• Rated control supply current IS
  typ. 50 mA
• Filter time
  max. 2 ms (at A1-A2; test pulse width)
• Inrush current
  min. 1 mA
• Contact type
  1 confirmation current path
• Limiting continuous current
  100 mA
• Output fuse
  150 mA fast blow
• Typical release time at US
  < 35 ms (when controlled via A1)
• Relay type
  Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3
• Mounting type
  DIN rail mounting
Indication
1 x red LED
Conductor cross-section flexible with ferrule without plastic sleeve
0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Safety Integrity Level (SIL)
3
Overvoltage category
III
ATEX
 II 3 G Ex nA nC IIC T4 Gc
Environmental simulation test
ISA-S71.04 (G3)
ECLASS 11.0
27371819
ETIM 6.0
EC001449
Width
12.5 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Input voltage range "0" signal
0 V DC ... 5 V DC (for safe Off)
Protective circuit
Serial protection against polarity reversal 33 V suppressor diode (A1/A2)33 V suppressor diode (31/A2)
Output description
PNP
Switching capacity
min. 20 mW
Switching frequency
max. 0.5 Hz
Typical pickup time at US
< 100 ms (with Us when controlled via A1)
Nominal operating mode
100% operating factor
Degree of protection
IP20
Status display
1 x green LED
Conductor cross section flexible
0.2 mm² ... 1.5 mm²
Conductor cross section solid
0.2 mm² ... 1.5 mm²
Standards/regulations
DIN EN 50178, EN 60079-15
IECEx
Ex nA nC IIC T4 Gc
REACh SVHC
Lead 7439-92-1
ECLASS 4.1
40020600
ECLASS 6.0
27371800
Height
116.6 mm
Maximum altitude
≤ 2000 m (Above sea level)
Diagnostic supply voltage UD
24 V DC -15 % / +10 % (31/A2, TBUS)
Number of outputs
1 (non-safety-related)
Mechanical service life
10x 106 cycles
Voltage
approx. 22 V DC (UD - 2 V)
Maximum inrush current
500 mA (Δt = 1 ms at Us)
Recovery time
500 ms
Min. degree of protection of inst. location
IP54
Housing material
PBT
pluggable
Yes
Conductor cross-section flexible with ferrule and plastic sleeve
0.25 mm² ... 1.5 mm² (only together with CRIMPFOX 6)
Rated surge voltage/insulation
Safe isolation, 6 kV reinforced insulation from control circuit, start circuit, confirmation current path, signal output to the enabling current path; 4 kV/basic insulation between all current paths and housing
Degree of pollution
2
GL
C, EMC2
ECLASS 4.0
40020600
ECLASS 5.0
27371900
Input current at UD
6 mA (at 31-A2 for UD; depending on load + 100 mA at M1 and 32)
Inrush current at UD
typ. 2.5 A (Δt < 20 µs at UD)
Switching voltage
min. 20.4 V DC
Switching capacity according to IEC 60947-5-1
4 A (24 V (DC13); N/O contact 13/14)
Short-circuit protection
no
Net weight
182.1 g
Assembly instructions
See derating curve
Operating voltage display
1 x yellow LED
Conductor cross-section AWG
24 ... 16
Stop category
0
Shock
15g
UL, USA/Canada
cULus
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 5.1
27371900
ETIM 7.0
EC001449
Designation
Air clearances and creepage distances between the power circuits
Current
max. 100 mA
Mounting position
vertical, horizontal, with front of module upward
Housing color
yellow
Connection method
Push-in connection
Stripping length
8 mm
Rated insulation voltage
250 V AC
Vibration (operation)
10 Hz ... 150 Hz, 2g
Conformance
CE-compliant
ECLASS 10.0.1
27371819
ECLASS 7.0
27371819
ECLASS 9.0
27371819