1211222 Phoenix Contact Electrical Wires & Cables

Product Details

• Withdrawal force
  < 100 N
• Customer variations
  On request
• Type
  Locking actuator right
• Height
  140.25 mm
• Depth
  133.5 mm
• Max. altitude
  4000 m (above sea level)
• Number of power contacts
  3 (PE, DC+, DC-)
• Number of signal contacts
  2 (CP, PP)
• Charging mode
  Mode 4
• Standards/regulations
  DIN EN 60751
• Note on the connection method
  Crimp connection, cannot be disconnected
• Maximum charging power
  250 kW
• Rated current of power contacts
  250 A DC
• Rated current for signal contacts
  2 A
• Insertion/withdrawal cycles
  > 10000
• Mounting position of the locking actuator
  Right-side
• Locking type
  Locking in the inserted state with a locking mechanism
• External sheath, color
  Green-yellow
• Number of positions of theconnectors
  4
• Maximum voltage for locking detection
  12 V
Service life insertion cycles
> 10000 load cycles
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
Tolerance at the sensor with the recommended measured current
±3K
Shutdown temperature
90 °C
Conductor length
2 m (DC cables)
Bore dimensions
117.65 mm x 90 mm, 117.65 mm x 83 mm
Rated voltage for power contacts
1000 V DC
Resistor coding
4.7 kΩ (between PE and PP)
Insertion force
< 100 N
Required mounting screws
M6
Design line
Generation 4
Housing color
black
External cable diameter
1.6 mm -0.2 mm
Possible power supply range at the motor
9 V ... 16 V
Reverse current of the motor
max. 1.5 A
Temperature coefficient (TCR)
3850 ppm/K
ECLASS 11.0
27144706
Design
Generation 4
Note
A protective cap is supplied as standard for the DC contacts.
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Insulation resistance of neighboring contacts
> 200 MΩ
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Screws included in the scope of delivery
none
Cable resistance
≤ 37.1 Ω/km
Minimum bending radius
15 mm
Cable weight
7 kg/km
Pause time after entry or exit path
3 s
Recommended adaptation time
600 ms
Type of sensor
Pt 1000
Temperature range
-40 °C ... 130 °C
Application
For charging with direct current (DC)
Charging standard
CCS type 2
Width
108 mm
Ambient temperature (operation)
-40 °C ... 80 °C
Type of charging current
DC
Rated voltage for signal contacts
30 V AC
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Mounting hole diameter
6.80 mm (ø)
Material
Plastic
Flammability rating
V0
Material surface of contacts
Ag
Operating voltage
12 V (Typical power supply at the motor)
Typical motor current for locking
0.25 A
Cable length
1 m
Mechanical emergency release
available
ECLASS 10.0.1
27144706
Cable structure
4 x 0.5 mm²
Outer sheath, material
PVC
Single wire, color
black PP/CS
Max. dwell time with reverse current
1 s
Lock recognition
available
Long-term stability (max. R0-Drift)
≤ 0.1 % (After 1000 hours at 130°C)
ECLASS 9.0
27144706