1211210 Phoenix Contact Electrical Wires & Cables

Product Details

• Design
  Generation 4
• Charging standard
  CCS type 2
• Note
  A protective cap is supplied as standard for the DC and AC contacts.
• Conductor length
  2 m (AC cables)
• Number of power contacts
  7 (L1, L2, L3, N, PE, DC+, DC-)
• Rated current for signal contacts
  2 A
• Type
  Locking actuator right
• Charging mode
  Mode 2, 3, 4
• Depth
  128.4 mm
• Ambient temperature (operation)
  -30 °C ... 50 °C
• Number of phases
  3
• Rated voltage for power contacts
  480 V AC
• Resistor coding
  4.7 kΩ (between PE and PP)
• Withdrawal force
  < 100 N
• Mounting position of the locking actuator
  Right-side
• Mounting hole diameter
  6.80 mm (ø)
• Flammability rating
  V0
• Material surface of contacts
  Ag
• External sheath, color
  Green-yellow
• Single wire, color
  black PP/CS
Reverse current of the motor
max. 0.5 A
Lock recognition
available
ECLASS 10.0.1
27144706
ECLASS 9.0
27144706
Application
For charging with alternating current (AC) and with direct current (DC)
Note on the connection method
Crimp connection, cannot be disconnected
Bore dimensions
117.65 mm x 90 mm, 117.65 mm x 83 mm
Max. altitude
4000 m (above sea level)
Type of charging current
DC, AC 3-phase
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Insertion force
< 100 N
Required mounting screws
M6
Housing color
black
Cable resistance
≤ 37.1 Ω/km
Minimum bending radius
15 mm
Operating voltage
24 V (Typical power supply at the motor)
Max. dwell time with reverse current
1 s
Type of sensor
Pt 1000
Resistance range
650 Ω ... 1450 Ω
Standards/regulations
DIN EN 60751
Width
108 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Maximum charging power
125 kW
Number of signal contacts
2 (CP, PP)
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Design line
Generation 4
Customer variations
On request
Cable structure
4 x 0.5 mm²
Outer sheath, material
PVC
Maximum voltage for locking detection
30 V
Service life insertion cycles
> 10000 load cycles
Mechanical emergency release
available
Temperature range
-40 °C ... 130 °C
ECLASS 11.0
27144706
Height
130.4 mm
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Rated current of power contacts
32 A AC
Rated voltage for signal contacts
30 V AC
Insulation resistance of neighboring contacts
> 200 MΩ
Screws included in the scope of delivery
none
Locking type
Locking in the inserted state with a locking mechanism
Cable weight
7 kg/km
Number of positions of theconnectors
4
Cable length
0.5 m
Tolerance at the sensor with the recommended measured current
±5K
Temperature monitoring
AC contacts: PTC chain (DIN˽EN˽60738-1)
Insertion/withdrawal cycles
> 10000
Material
Plastic
External cable diameter
1.6 mm -0.2 mm
Possible power supply range at the motor
22 V ... 26 V
Recommended adaptation time
600 ms
Typical motor current for locking
0.05 A
Pause time after entry or exit path
3 s
Recommended measured current
≤ 1 mA (Umax= 16 V DC)