1173451 Phoenix Contact Control Relays

Product Details

• Nominal input voltage UN
  24 V DC
• Contact type
  4 changeover contacts
• Min. switching current
  5 mA (at 24 V)
• Test voltage
  2.5 kVrms (50 Hz, 1 min., winding/contact)
• Assembly instructions
  In rows with zero spacing
• Conductor cross section solid
  0.5 mm² ... 4 mm²
• Conductor cross section AWG
  20 ... 10 (solid)
• Rated surge voltage
  2.5 kV
• ECLASS 10.0.1
  27371601
• ECLASS 5.1
  27371600
• ECLASS 7.0
  27371601
• UNSPSC 6.01
  30211917
• UNSPSC 12.01
  39121516
• Height
  89 mm
• Maximum altitude
  ≤ 2000 m
• Typical response time
  13 ms
• Contact material
  AgNi
• Limiting continuous current
  6 A
• Mechanical service life
  approx. 2x 107 cycles
• Connection name
  Contact side
Stripping length
8 mm
Standards/regulations
DIN EN 50178
Overvoltage category
II
ECLASS 5.0
27371600
ECLASS 9.0
27371601
ETIM 2.0
EC001437
UNSPSC 20.0
39122334
Utilization restriction
EMC: class A product, see manufacturer's declaration in the download area
Input voltage range in reference to UN
see diagram
Typical release time
14 ms
Status display
Yellow LED
Type of switch contact
Single contact
Maximum switching voltage
250 V AC/DC
Switching capacity min.
48 mW
Flammability rating according to UL 94
V2 (Housing)
Connection method
Screw connection
Conductor cross section flexible
0.5 mm² ... 4 mm²
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 6.0
27371600
ETIM 6.0
EC001437
UNSPSC 7.0901
39121516
UNSPSC 19.0
39122334
UNSPSC 18.0
39122334
Width
27 mm
Ambient temperature (operation)
-40 °C ... 60 °C
Typical input current at UN
42 mA
Note
the following values are applicable if a gold layer is destroyed
Maximum inrush current
16 A (20 ms, N/O contacts)
Switching capacity
2 A (at 24 V, DC13)
Torque
0.5 Nm ... 0.6 Nm
Insulation
Basic insulation
Designation
Corrosive gas test
ECLASS 11.0
27371601
ETIM 4.0
EC001437
UNSPSC 11
39121516
Depth
75 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Degree of protection
IP20 (Relay base)
Protective circuit
Damping diode
Power dissipation for nominal condition
1.01 W
Minimum switching voltage
5 V (At 24 mA)
Interrupting rating (ohmic load) max.
144 W (at 24 V DC)
Operating mode
100% operating factor
Mounting position
any
Conductor cross-section solid (2 conductors with same cross section)
0.5 mm² ... 2.5 mm²
Conductor cross section flexible (2 conductors with same cross section)
0.5 mm² ... 2.5 mm²
Rated insulation voltage
250 V AC
Pollution degree
2
Identification
ISA-S71.04. G3 Harsh Group
ETIM 3.0
EC001437
ETIM 7.0
EC001437
UNSPSC 13.2
39122334
UNSPSC 21.0
39122334